__ a Put the lever (130) in position on the release-lever (127).
_  b Install the screw (128) and the washer (129) but tighten

_
 the screw by hand only.

 NOTE : The adjustment of the release-lever (127) is done
____ after the complete installation of the emergency escape-slide release-mechanism assembly.
 c Apply COMMON GREASE (Material No. 04-004) to the splines of
_
 the release-lever (127).

 d Install the release-lever (127) on the shaft-end of the
_
 camshaft assembly (121).

 NOTE : The punch mark "C" on the release-lever (127) must
____ align with the punch mark "D" on the shaft-end of the camshaft assembly (121).
 e Install the bolt (125) and the washer (126).
_
 12 Install the release-lever (113):

__ a Apply COMMON GREASE (Material No. 04-004) to the splines of
_
 the release-lever (113).

 b Put the spacer (114) in position on the shaft-end of the
_
 camshaft assembly (121).

 c Install the release-lever (113) on the shaft-end of the
_
 camshaft assembly (121).

 NOTE : The punch mark "A" on the release-lever (113) must
____ align with the punch mark "B" on the shaft-end of the camshaft assembly (121).
 d Install the washer (112) and the castellated nut (111).
_
 e Install the new cotter pin (110).

_
 (2) Install the release-mechanism lever assembly: (Ref. Fig. 407/TASK 25-62-43-991-006)
 (a) Assemble the lever assembly (83): 1 Apply COMMON GREASE (Material No. 04-004) to the bushes (102).
_  2 Put the bushes (102) in position in the levers (100) and

_
 (101).

 3 Put the washers (96) and the bolts (95) together with the
_ washers (97) and the bushes (98) in position on the lever (100).
 4 Put the lever (101) in position and install the nuts (99), but
_
 do not tighten the nuts at this time.

 5 Make sure that the levers (100) and (101) are aligned and
_
 tighten the nuts (99).

 6 Apply COMMON GREASE (Material No. 04-004) to the bushes (104).
_
 7 Put the bushes (104) in position in the double lever (105).

_
 8 Put the double lever (105) in its position between the levers

_

 (100) and (101).
 9 Adjust the lever assembly (83):

_ a Measure the distance between the double lever (105) and the
_ levers (100) and (101) with a feeler gage (see DETAIL "B").
 b Make sure that the distance is not more than
_
 0.9 mm (0.0354 in.). c If the distance between the levers is not in this tolerance
_
 adjust the distance with the washers (103).

 (b) Assemble the release-mechanism lever assembly (82): 1 Install the setscrew (93), the locking device (92) and the nut
_
 (91).

 2 Apply COMMON GREASE (Material No. 04-004) to the bushes (89)
_
 and (90).

 3 Put the bushes (89) and (90) in position in the lever bracket
_
 (94) as recorded in the removal procedure. 4 Apply COMMON GREASE (Material No. 04-004) to the bolt (88).
_ 5 Put the lever assembly (83) in position in the lever bracket
_ (94) and install the bolt (88).

 6 Adjust the release-mechanism lever assembly (82):
_ a Measure the distance between the lever assembly (83) and
_ the lever bracket (94) with a feeler gage (see DETAIL "B").
 b Make sure that the distance is not more than
_
 0.9 mm (0.0354 in.). c If the distance between the levers is not in this tolerance
_ adjust the distance with the washers (84).
 d Remove the bolt (88) and install the washers (84) as
_
 necessary.

 7 Install the bolt (88), the washer (87) and the castellated nut
_
 (86).

 8 TORQUE the castellated nut (86) to between 0.30 and 0.35 m.daN
_ (26.54 and 30.97 lbf.in) and install the new cotter pin (85).
 (c)
 Apply SEALANTS (Material No. 09-019) to the mating surface of the release-mechanism lever assembly (82).

 (d)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (80).

 (e)
 Put the release-mechanism lever assembly (82) in position and install the bolts (80) and the nuts (81).

 (3)
 Install the release-mechanism tie-rod assembly: (Ref. Fig. 406/TASK 25-62-43-991-005)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(100)