(a)
 Apply SEALANTS (Material No. 09-019) to the mating surface of the bracket (75).

 (b)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (71) and (73).

 (c)
 Put the bracket (75) in position and install the bolts (71) and (73), and the nuts (72) and (74).

 (d)
 Apply COMMON GREASE (Material No. 04-004) to the bushes (59) and (60).

 (e)
 Put the bushes (59) and (60), together with the tie-rod assembly (54), in position on the camshaft-assembly as recorded in the removal procedure.

 (f)
 Install the bolt (58), the washer (57) and the castellated nut (56).

 (g)
 Install the new cotter pin (55).

 (h)
 Apply COMMON GREASE (Material No. 04-004) to the bushes (52) and (53).

 (i)
 Put the bushes (52) and (53), together with the other end of the tie-rod assembly (54), in position on the lever-assembly as recorded in the removal procedure.

 (j)
 Install the bolt (50) and the washer (48) to hold the tie-rod assembly (54) in position.

 (k)
 Assemble the over-center spring-rod assembly (63) (reffered to as the spring-rod assembly):

 (l)
 Apply COMMON GREASE (Material No. 04-004) to the bushes (69) and (70).

 (m)
 Put the bushes (69) and (70), together with the spring-rod assembly (63), in position on the bracket (75) as recorded in the removal procedure.

 (n)
 Install the bolt (68), the washers (67) and (66), and the castellated nut (65).

 (o)
 Install the new cotter pin (64).

 (p)
 Apply COMMON GREASE (Material No. 04-004) to the bushes (61) and (62).

 (q)
 Put the bushes (61) and (62), together with the other end of the spring-rod assembly (63), in position on the lever assembly as recorded in the removal procedure.

 (r)
 Install the bolt (51) and the washer (49) to hold the spring-rod assembly (63) in position.

 (s)
 Install the washers (47) and the castellated nuts (46).

 (t)
 Install the new cotter pins (45).

 (4)
 Install the release-mechanism proximity-detector assemblies (referred to as the proximity-detector assemblies):

 1_ Apply COMMON GREASE (Material No. 04-004) to the spring (43)
 and on the inside surface of the bellows (40).
 2_ Put the spring (43) in position in the bellows (40).
 3_ Apply COMMON GREASE (Material No. 04-004) to the shaft of the
 tie-rod end (44).
 4_ Put the tie-rod ends (42) and (44) together with the bushes
 (41) in position.
 5_ Make sure that the tie-rod ends are correctly installed in the
 spring (43).

 (Ref. Fig. 405/TASK 25-62-43-991-004)
 (a) Assemble the proximity-detector assemblies:
 1_ Apply COMMON GREASE (Material No. 04-004) to the actuating rod
 (22).
 2_ Put the actuating rod (22) a short distance in position in the
 switch-bracket (36).
 3_ Put the washer (23), the nut (24) and the washer (25) in
 position on the actuating rod (22).
 4_ Apply COMMON GREASE (Material No. 04-004) to the spring (26).
 5_ Put the spring (26) and the bush (27) in position in the
 switch-bracket (36) and push the actuating rod (22) in
 position.
 6_ Put the bush (21) in position and install the washers (23) and
 the nut (24).
 7_ Put the washer (28), the rod-guide (29) and the target
 assembly (30) in position.
 8_ Put the serrated washer (31) in position and install the nut

 (32).
 (b)
 Apply SEALANTS (Material No. 09-019) to the mating surfaces of the proximity-detector assemblies (20).

 (c)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (35).

 (d)
 Put the proximity-detector assemblies (20) in position on the frame structure, and install the bolts (35), the washers (34) and the nuts (33).

 (e)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the pins (38).

 (f)
 Put the pins (38) in position in the frame structure and install the nuts (37).

 (5) Adjust the over-center spring-rod assembly (reffered to as the spring-rod assembly):
 (Ref. Fig. 409/TASK 25-62-43-991-008)
 (a)
 Cut, remove and discard the lock-wire from the lock-nut (1) of the eye-end fitting.

 (b)
 Loosen the lock-nut (1) of the eye-end fitting.