4_ Apply COMMON GREASE (Material No. 04-004) to the spring (26).
 5_ Put the spring (26) and the bush (27) in position in the
 switch-bracket (36) and push the actuating rod (22) in
 position.
 6_ Put the bush (21) in position and install the washer (23) and
 the nut (24).
 7_ Put the washer (28), the rod-guide (29) and the target
 assembly (30) in position.
 8_ Put the serrated washer (31) in position and install the nut
 (32).

 (b)
 Apply SEALANTS (Material No. 09-019) to the mating surface of the proximity-detector assembly (20).

 (c)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (35).

 (d)
 Put the proximity-detector assembly (20) in position on the frame structure, and install the bolts (35), the washers (34) and the nuts (33).

 (e)
 Apply SPECIAL MATERIALS (Material No. 05-002) on the thread of the pin (38).

 (f)
 Put the pin (38) in position in the frame structure and install the nut (37).

 (5) Adjust the over-center spring-rod assembly (reffered to as the spring-rod assembly):
 (Ref. Fig. 409A/TASK 25-62-43-991-008-A)
 (a)
 Cut, remove and discard the lock-wire from the lock-nut (1) of the eye-end fitting.

 (b)
 Loosen the lock-nut (1) of the eye-end fitting.

 (c)
 Move the latch lever rearward until it touches the lever bracket at POINT "A".

 (d)
 Move the double lever rearward until it touches the latch lever stop-bolt (2) at POINT "B".

 (e)
 Turn the adjusting-rod (3) and adjust the spring-rod assembly to

 53.0 +0.5 -0.5 mm (2.0866 +0.0196 -0.0196 in.).

 (f)
 Tighten the lock-nut (1) of the eye-end fitting.

 (g)
 Safety the lock-nut (1) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).

 (h)
 Make sure that the rubber bellows of the spring-rod assembly is in its correct position after you have done the adjustment.

 (6)
 Install the rigid control-cable: (Ref. Fig. 404A/TASK 25-62-43-991-003-A)

 (a)
 Apply COMMON GREASE (Material No. 04-004) to the clevis-pin (4).

 (b)
 Put the rigid control-cable (1) together with the spacers (2) and (3), as recorded in the removal procedure, in position and install the clevis-pin (4).

 (c)
 Put the washer (5) in position and install the new Cotter pin (6).

 (7)
 Adjust the distance between the latch lever and the lever bracket: (Ref. Fig. 409A/TASK 25-62-43-991-008-A)

 (a)
 Cut, remove and discard the lock-wire from the lock-nuts (4) and the sleeve adjust-nuts (6) of the rigid control-cable (5).

 (b)
 Loosen the lock-nuts (4) of the rigid control-cable (5).

 (c)
 Turn the sleeve adjust-nut (6) and adjust the distance between the latch lever and the lever bracket at POINT "A" to 0.5 +0.1 -

0.1 mm (0.0196 +0.0039 -0.0039 in.).
 NOTE : Measure the distance, between the top of the lever bracket

____ and the lip of the latch lever with a feeler gage.
 (d)
 Loosen the sleeve adjust nut (6) FIVE FULL TURNS.

 (e)
 Tighten the lock-nuts (4) of the rigid control-cable (5).

 (f)
 Safety the lock-nuts (4) and the sleeve adjust-nut (6) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).

 (8) Adjust the clearence between the double lever and the latch lever: (Ref. Fig. 409A/TASK 25-62-43-991-008-A)
 (a)
 Cut, remove and discard the lock-wire from the lock-nuts (7) of the tie-rod (8).

 (b)
 Loosen the lock-nuts (7) of the tie-rod (8).

 (c)
 Make sure that the release lever (14) touches the stop screw (15) at POINT "D" (see DETAIL "C").

 (d)
 Turn the tie-rod (8) clockwise or counterclockwise to adjust the distance between the double lever and the latch lever at POINT "B".

 (e)
 Adjust the distance between the double lever and the latch lever at POINT "B" to 0.3 +0.1 -0.1 mm (0.0118 +0.0039 -0.0039 in.).

 NOTE : Measure the distance between the double lever and the
____ latch lever stop-bolt (2) with a feeler gage.
 (f)
 Make sure that the eye-ends of the tie-rod (8) are in safety. NOTE : If you cannot push a needle or equivalent through the
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(107)