(e)
 Connect the electrical connector (15):

 -
FOR 7500MM
 2871VC-A.

 -
FOR 7501MM
 2870VC-A.

 -
FOR 7502MM
 2873VC-A.

 -
FOR 7503MM
 2872VC-A.

R  EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 456 201-299, 301-399, 401-499, Aug 01/05
 CES

 (f)
 Install the upper attachments of the pack-assembly (9) with one of the two procedures:

 (g)
 Procedure 1:

 1  Make sure that the head of each mounting pin (42) extends a
_
 minimum of 25.0 mm (0.98 in.) from the door.

 2  Make sure that the quick-release latches (43) are in a good
_
 condition, and retracted to the disengaged position.

 NOTE : You can retract the quick-release latches (43) to the
____
 disengaged position with:

 -Your hand.
 -Or, when you carefully pull the PULL handles (44). 3 Push the pack-assembly (9) against the door.
_
 4 Engage the quick-release latches (43):

_ CAUTION : DO NOT USE A TOOL OR A METAL OBJECT TO ENGAGE THE
_______ QUICK- RELEASE LATCHES. IF YOU DO, YOU CAN CAUSE DAMAGE TO THE PACK-ASSEMBLY.
 a  Use your fingers to engage the quick-release latches (43)
_
 with the mounting pins (42).

 5  Make sure that there is no play between the packboard (13) and
_
 the door.

 6  If there is play, carefully tighten the mounting pins (42)
_
 until the movement stops.

 NOTE : If you must tighten the mounting pins (42), make sure
____ that you do not cause the quick-release latches (43) to disengage.
 (h)
 Or.

 (i)
 Procedure 2: 1 Push the pack-assembly (9) against the door.

_
 2 Install the stud assemblies (45) in the door.

_
R  EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 457 201-299, 301-399, 401-499, Aug 01/05
 CES

 3_ Carefully tighten the stud assemblies (45) with the Allen key
 (49) and torque to between 50.0 and 56.0 lbf.in (0.56 and 0.63
 m.daN).
 NOTE : Make sure that the Allen key (49) goes through the wire____
 loop (50).
 4_ Make sure that there is no play between the packboard (13) and
 the door.
 5_ Connect the PULL handles (47) to the wire loops (50) with the
 attach links (48).
 NOTE : The PULL handles (47) are attached to the soft-cover____
 (13) of the pack-assembly (9). It is not necessary to
 remove the PULL handles (47) when you connect them to
 the stud assemblies (45).
 6_ Tighten the link nut (46).

 (3) Install the girt bar (10) in the floor fittings (26): CAUTION : DO NOT OPEN THE PASSENGER/CREW DOOR. IF YOU DO, YOU WILL
_______ START THE SEQUENCE OF STEPS THAT PULLS THE INFLATABLE ASSEMBLY OUT OF THE PACK-ASSEMBLY.
 (a)
 Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) (4) and set the emergency control-handle (3) to the ARMED position.

 (b)
 Carefully lift the door with the door control-handle (2).

 (c)
 Hold the door in this position, to prevent it to open fully.

 (d)
 Install the girt bar (10): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN

_______ THE PACK ASSEMBLY.
 1  Push the girt bar (10) into the floor fittings (26), until the
_ spring pawls (29) click into position.
 2  Make sure that the stiff part of the girt assembly (11) is
_ folded outboard over the girt bar (10). See SECTION T-T.
 (e) Carefully lower, and lock the door with the door control-handle (2).
R  EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 458 201-299, 301-399, 401-499, Aug 01/05
 CES

 (f)
 Make sure that the control-shaft levers (28), have engaged correctly in the holes in the girt bar (10).

 (g)
 Set the emergency control-handle (3) to the DISARMED position.

 (h)
 Carefully lift the door with the door control-handle (2).

 (i)
 Hold the door in this position, to prevent it to open fully.

 (j)
 Make sure that the girt bar (10) has engaged correctly with the telescopic forks (27) of the door structure.

 (k)
 Carefully lower, and lock the door with the door control-handle (2).

 (l)
 Set the emergency control-handle (3) to the ARMED position.