(b)
An incorrect indication is shown when the needle is to the left of the GREEN cursor.
(c)
If the gage (11) shows an incorrect indication:
-When the temperature conditions become stable, examine the gage
(11) again.
-If the gage (11) continues to show an incorrect indication, replace the inflation reservoir (5).
(5) Pulley assembly (4) and (7) adjustment procedure:
NOTE : If there are no RED index-marks, pulley assembly adjustment is
____ not necessary.
(a)
If you can see RED index-marks (38) on the pulley assemblies (4) and (7), do these steps:
(b)
Make sure that the RED index-marks (38) are opposite each other, or in the permitted tolerance. A tolerance of 1.00 mm (0.039 in.) is permitted between the center lines of each index-mark.
(c)
If the RED index-marks (38) are not opposite each other, or in the permitted tolerance, do these steps:
1_ Loosen the bolt (36) and the nut (37).
2_ Turn the two shells (35) until the RED index-marks (38) align,
or are in the permitted tolerance.
3_ Tighten the bolt (36) and the nut (37) and torque the nut (37)
to between 0.95 and 1.05 m.daN (84.07 and 92.92 lbf.in).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-46Page 415 201-299, 401-499, Aug 01/05
CES Subtask 25-62-46-420-050
B. Installation of the Inflation Reservoir 7506MM (7507MM)
(Ref. Fig. 401/TASK 25-62-46-991-001)
WARNING : BE CAREFUL WITH THE INFLATION RESERVOIR AND ITS COMPONENTS. THE
_______ RESERVOIR IS AN ALUMINUM BOTTLE WOUND IN KEVLAR FIBERS BONDED WITH EPOXY RESINS, AND IS PRESSURIZED WITH GAS. IF YOU CAUSE DAMAGE TO THE RESERVOIR, THERE IS A RISK OF EXPLOSION. NO DAMAGE IS PERMITTED.
(1)
Put the inflation reservoir (5) in the support bracket (8), until it is against the back of the support bracket (8).
(2)
Remove the pressure seal cap (20) from the bulkhead connection (9).
(3)
Put the pressure seal cap (20) in the pocket (3).
(4)
Remove the blanking plugs from the disconnected line ends.
(5)
Connect the hose assembly (10) to the bulkhead connection (9), and torque it to between 3.0 and 3.2 m.daN (22.12 and 23.59 lbf.ft).
(6)
Carefully put the hose assembly (10) adjacent to the support bracket (8).
(7)
Make sure that there are no kinks in the hose assembly (10).
(8)
Install, and tighten the bolt (14), the washer (15), the clamp (16) and the spacer (17).
(9)
Tighten the clamps (13).
(10)
Remove the blanking caps from the electrical connectors.
(11)
Make sure that the electrical connectors are clean and in the correct condition.
(12)
Remove the blanking plug (22) from the socket (24) and connect it to the dummy socket (23).
(13)
Connect the electrical connector (21) to the socket (24):
-
FOR 7506MM
7555VC-A.
-
FOR 7507MM
7556VC-A.
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-46Page 416 201-299, 401-499, Aug 01/05
CES
(14) Connect the wire-control assembly (2) to the flexible control-assembly (1):
CAUTION : DO NOT PUT WEIGHT ON THE FWD PULLEY WHEN YOU CONNECT THE
_______ WIRE- CONTROL ASSEMBLY TO THE FLEXIBLE CONTROL-ASSEMBLY. WEIGHT ON THE PULLEY CAUSES TENSION IN THE WIRE, WHICH CAN CAUSE THE END OF THE WIRE TO BREAK.
CAUTION : DO NOT PUSH THE END OF THE WIRE INTO THE WIRE-CONTROL
_______ ASSEMBLY. THIS CAN CAUSE A KINK IN THE WIRE.
(a)
Remove the protection plug (32) from the sleeve nut (18) to get access to the two clips (31).
(b)
Make sure that you do not push the end of the wire (25) into the wire-control assembly (2).
(c)
Remove, and keep the two clips (31).
(d)
Put the protection plug (32) in the pocket (3).
(e)
Carefully push the end of the wire (25) into the slot of the flexible control-assembly (1).
(f)
Put the two clips (31) around the connection of the two control assemblies, and tighten the sleeve nut (18).
(g)
Safety the sleeve nut (18) with lockwire MISCELLANEOUS (Material No. 19-010) (19).
(15) Do these steps if there is tension and/or torsion in the wire-control assembly (2):
(a)
To release tension:
(b)
To release torsion: 1 At the pulley assembly (4) remove the lockwire (34) and loosen
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM EQUIPMENT/FURNISHINGS 設(shè)備4(129)
