(12)
 Remove the tie-down fitting (36):

 (a) Remove the nuts (37), and remove the screws (35) from the tie-down fitting (36).
 (b) Remove the tie-down fitting (36) from the structure (3). **ON A/C 301-399,
 Subtask 25-55-41-020-050-B
 A. Removal of the Tie-Down and Net Attachment Fittings from the Floor Area of the AFT Cargo-Compartment (Ref. Fig. 401B/TASK 25-55-41-991-001-B)
 (1)
 Remove the cargo net(s) (5), if installed:

 (a)
 Disconnect the net fittings (6) from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.

 (b)
 Remove the cargo net(s) (5).

 (2)
 Remove the tie-down points (2): NOTE : The removal procedure for all the tie-down points (2) is the

____ same. Therefore, the removal procedure for one tie-down point
 (2) only is given here.
R  EFF : 062-099, 106-149, 151-199, 203-299, 25-55-41Page 413 301-399, 401-499, Aug 01/05
 CES

R  Tie-Down and Net Attachment Fittings - AFT Cargo-Compartment Floor Area 
R  Figure 401B/TASK 25-55-41-991-001-B12 (SHEET 1) 
R  EFF :  301-399,  25-55-41 Page 414 
May 01/04
 CES 

R  Tie-Down and Net Attachment Fittings - AFT Cargo-Compartment Floor Area 
R  Figure 401B/TASK 25-55-41-991-001-B22 (SHEET 2) 
R  EFF :  301-399,  25-55-41 Page 415 
May 01/04
 CES 

 (a)
 Remove the nuts (4), and remove the screws (1) from the tie-down point (2).

 (b)
 Remove the tie-down point (2) from the structure (3).

 (3) Remove the tie-down points (8): NOTE : The removal procedure for all the tie-down points (8) is the
____ same. Therefore, the removal procedure for one tie-down point
 (8) only is given here.
 (a)
 Remove the nuts (10), and remove the screws (7) from the tie-down point (8).

 (b)
 Remove the tie-down point (8) from the plug housing (9).

 (c)
 If necessary, remove the plug housing (9) from the structure (3).

 (4) Remove the tie-down fittings (12): NOTE : The removal procedure for all the tie-down fittings (12) is
____ the same. Therefore, the removal procedure for one tie-down fitting (12) only is given here.
 (a)
 Remove the nuts (13), and remove the screws (11) from the
 tie-down fitting (12).

 (b)
 Remove the tie-down fitting (12) from the structure (3).

 (5) Remove the tie-down fittings (15): NOTE : The removal procedure for all the tie-down fittings (15) is
____ the same. Therefore, the removal procedure for one tie-down fitting (15) only is given here.
 (a)
 Remove the nuts (16), and remove the screws (14) from the
 tie-down fitting (15).

 (b)
 Remove the tie-down fitting (15) from the structure (3).

 (6) Remove the tie-down fittings (18): NOTE : The removal procedure for all the tie-down fittings (18) is
____ the same. Therefore, the removal procedure for one tie-down fitting (18) only is given here.
 EFF : 301-399, 25-55-41Page 416

Aug 01/05
R
 CES

 (a)
 Remove the nuts (19), and remove the screws (17) from the tie-down fitting (18).

 (b)
 Remove the tie-down fitting (18) from the structure (3).

 (7) Remove the seat-track sections (21): NOTE : The removal procedure for all the seat-track sections (21) is
____ the same. Therefore, the removal procedure for one seat-track section (21) only is given here.
 (a)
 Remove the nuts (22), and remove the screws (20) from the seat-track section (21).

 (b)
 Remove the seat-track section (21) from the structure (3).

 (8)
 Remove the tie-down fitting (24):

 (a)
 Remove the nuts (25), and remove the screws (23) from the tie-down fitting (24).

 (b)
 Remove the tie-down fitting (24) from the structure (3).

 (9)
 Remove the tie-down fittings (27): NOTE : The removal procedure for all the tie-down fittings (27) is

____ the same. Therefore, the removal procedure for one tie-down fitting (27) only is given here.
 (a)
 Remove the nuts (28), and remove the screws (26) from the tie-down fitting (27).

 (b)
 Remove the tie-down fitting (27) from the structure (3).

 (10)
 Remove the tie-down fitting (30):
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設(shè)備4(44)