A. Get Access
(1) Remove/open the access panel to the escape-slide inflation reservoir (Ref. TASK 25-62-49-000-001).
4. Procedure
_________ (Ref. Fig. 402/TASK 25-62-00-991-005) Subtask 25-62-00-210-064
A. Inspection:
(1)
Do a check of the pressure gage installed on the escape slide inflation-reservoir:
(2)
Make sure that the pointer of the pressure gage is in or above the green 'GO' band.
NOTE : The green 'GO' band of the pressure gage is temperature
____ compensated and moves independently of the pointer when temperature changes occur.
(3)
If the pointer is above the green 'GO' band upper limit, a 'GO' condition is permitted.
(4)
If the pointer is below the green 'GO' band lower limit, you must:
(a)
Wait for temperature conditions to become stable and do Step (1) again.
or
(b)
Replace the inflation reservoir (Ref. TASK 25-62-49-000-001).
5. Close-up
________ Subtask 25-62-00-410-060
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install/Close the inflation reservoir access-panel (Ref. TASK 25-62-49-400-001).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : 301-399, 25-62-00Page 410
May 01/05
R
CES
Inflation Reservoir Pressure-Gage Figure 402/TASK 25-62-00-991-005
R EFF : 301-399, 25-62-00 Page 411 May 01/05
CES
**ON A/C ALL
TASK 25-62-00-040-006 Pre-Flight Installation of the Enclosure Door, when the Escape-Slide is Removed
1. Reason for the Job
__________________
Refer to the MMEL TASK: 25-60-02-B)
Emergency - Escape Slide/Slide Raft
Overwing Emergency Exit
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific 1 ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific 1 SCREWDRIVER - PHILLIPS HEAD
No specific 1 WARNING NOTICE
98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking Tool (98D27803000000)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
25-62-00-991-014 Fig. 403
EFF : ALL
25-62-00Page 412
**ON A/C ALL
3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 25-62-00-860-064
A. Aircraft Maintenance Configuration
(Ref. Fig. 403/TASK 25-62-00-991-014)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. NOTE : The lock pin (3) and the pressure blanking-plug (7) are kept in a
____ pocket, which attaches to the inflation reservoir (1).
(1)
If the inflation reservoir (1) is charged, install the lock pin (3) in the regulator valve assembly (2).
(2)
Safety the flaps (Ref. TASK 27-00-00-480-002).
(3)
Put a WARNING NOTICE on the slat/flap control lever to tell persons not to operate the flaps, during the installation procedure.
(4)
Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position adjacent to the related enclosure (4).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(67)
