R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL
25-54-41Page 416
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump
**ON A/C 001-049, 051-099, 101-149, 201-299,
25-54-41-991-001 Fig. 401 R **ON A/C 151-199, 401-499,
25-54-41-991-001-A Fig. 401A
**ON A/C 301-399,
25-54-41-991-001-B Fig. 401B
**ON A/C 001-049, 051-099, 101-149, 201-299,
25-54-41-991-002 Fig. 402 R **ON A/C 151-199, 401-499,
25-54-41-991-002-A Fig. 402A
**ON A/C 301-399,
25-54-41-991-002-B Fig. 402B
**ON A/C ALL
25-54-41-991-003 Fig. 403
EFF : ALL
25-54-41Page 417
3. Job Set-up
__________
Subtask 25-54-41-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the FWD cargo-compartment door is open and safetied with the actuator safety lock (Ref. TASK 52-30-00-860-001).
(2)
Make sure that the access platform is in position at the opening of the FWD cargo-compartment door.
4. Procedure
_________
Subtask 25-54-41-910-050
A. Preparation for Installation:
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1)
Do an inspection of the component interface and/or the adjacent area.
(2)
Use a non-metal scraper to remove the old sealant from the component interface and the adjacent area.
(3)
Use a lint-free cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-003) to clean the component interface and the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(5)
Apply the SPECIAL MATERIALS (Material No. 05-002) to the threads of the screws which attach the tie-down and net attachment fittings.
EFF : ALL
25-54-41Page 418
May 01/04
R
CES
R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 25-54-41-420-050
B. Installation of the Tie-Down and Net Attachment Fittings in the Floor Area (Ref. Fig. 401/TASK 25-54-41-991-001)
(1) Install the tie-down points (2): NOTE : The installation procedure for all the tie-down points (2) is
____ the same. Therefore, the installation procedure for one tie-down point (2) only is given here.
(a)
Put the tie-down point (2) in position at the structure (3).
(b)
Install the screws (1) in the tie-down point (2).
(2)
Install the seat-track section (5):
(a)
Put the seat-track section (5) in position at the structure (3).
(b)
Install the screws (4) in the seat-track section (5).
(3)
Install the tie-down points (9): NOTE : The installation procedure for all the tie-down points (9) is
____ the same. Therefore, the installation procedure for one tie-down point (9) only is given here.
(a)
If removed, put the plug housing (10) in position at the structure (3).
(b)
Put the tie-down point (9) in position at the plug housing (10).
(c)
Install the screws (8) in the tie-down point (9).
(4) Install the tie-down fittings (12): NOTE : The installation procedure for all the tie-down fittings (12)
____ is the same. Therefore, the installation procedure for one tie-down fitting (12) only is given here.
(a)
Put the tie-down fitting (12) in position at the structure (3).
(b)
Install the screws (11) in the tie-down fitting (12).
(5)
Install the tie-down fitting (14):
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(14)
