(c)
 Under the pack-assembly (9) disengage the straps (21), between the decorative-cover (20) and the girt assembly (11).

 (d)
 Carefully lower, and lock the door with the door control-handle (2).

 (e)
 Types 1 and 2:

 (f)
 Type 3: 1 Pull the lower edge of the decorative-cover (20) away from the

 1_ Pull the lower edge of the decorative-cover (20) away from the
 pack-assembly (9), to disengage the spring clips.
 2_ Carefully pull the top edge of the decorative-cover (20), from
 the attach-strips (16), and remove it.

_
 pack-assembly (9), to disengage the spring clips. 2 Disengage the spring loaded bolts (73) and remove the
_ decorative-cover (20).
 EFF : ALL
25-62-44Page 430

 (g) keep the decorative-cover (20) with the aircraft.
 (2) Safety the inflation reservoir of the escape-slide raft: WARNING : MAKE SURE THAT THE SAFETY/LOCK PIN IS CORRECTLY INSTALLED
_______ IN THE REGULATOR VALVE ASSEMBLY OF THE INFLATION RESERVOIR. THIS PREVENTS ACCIDENTAL:
 -DISCHARGE OF THE INFLATION RESERVOIR
 -DEPLOYMENT OF THE ESCAPE-SLIDE WHICH CAN CAUSE INJURY AND/OR DAMAGE.
 (a) Install the lock pin (18) in the regulator valve assembly (19). NOTE : The lock pin (18) is kept in a pocket (75) on the
____ soft-cover (12) of the pack-assembly (9).
 (3) Get access to the girt bar (10) and the floor fittings (26): CAUTION : DO NOT OPEN THE PASSENGER/CREW DOOR. IF YOU DO, YOU WILL
_______ START THE SEQUENCE OF STEPS THAT PULLS THE INFLATABLE ASSEMBLY OUT OF THE PACK-ASSEMBLY.
 (a)
 Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) (4) and set the emergency control-handle (3) to the ARMED/AUTOMATIC position.

 (b)
 Carefully lift the door with the door control-handle (2).

 (c)
 hold the door in this position, to prevent it to open fully.

 (d)
 Remove the girt bar (10): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN

 (e)
 Carefully lower, and lock the door with the door control-handle (2).

 (f)
 Set the emergency control-handle (3) to the DISARMED/MANUAL position, and install the SAFETY PIN - SLIDE ARMING (98D52103500000) (4).

_______
 THE PACK ASSEMBLY.
 1_ Push the spring pawls (29), to release the girt bar (10).
 2_ Pull the girt bar (10) inboard from the floor fittings (26).
 3_ Put the girt bar (10) on the cabin floor, inboard of the floor
 fittings (26).

R  EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 431 201-299, 301-399, 401-499, Aug 01/05
 CES  (4) Remove the pack-assembly (9) from the door:

 (a)
 Remove the upper attachments of the pack-assembly (9) with one of the two procedures:

 (b)
 Procedure 1:

 (c)
 Or.

 (d)
 Procedure 2: 1 Loosen the link nut (46).

 1_ Hold the pack-assembly (9).
 2_ Pull the PULL handles (44), to disengage the quick-release
 latches (43) from the mounting pins (42).

_ 2 Remove the attach-link (48) and PULL handle (47), from the
_ stud assembly (45).
 3  Keep the attach-link (48) and PULL handle (47), with the
_ pack-assembly (9).
 4  Hold the pack-assembly (9).
_ 5 Remove the stud assemblies (45) with the allen key (49) from
_ the door.
 NOTE : Make sure the allen key (49) goes through the wire loop
____ (50).
 6  Keep the stud assemblies (45) with the pack-assembly (9).
_
 (e)
 Let the pack-assembly (9) fall inboard on the supports (14), and continue to hold it.

 (f)
 Disconnect the electrical connector (15):

 -
FOR 7500MM 2871VC-A.

 -
FOR 7501MM 2870VC-A.

 -
FOR 7502MM 2873VC-A.

 -
FOR 7503MM 2872VC-A.

R  EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 432 201-299, 301-399, 401-499, Aug 01/05
 CES

 (g)
 Put blanking caps on the disconnected electrical connectors.

 (h)
 Lift the pack-assembly (9) from the supports (14) and put it on the cabin floor.

 NOTE : The pack-assembly (9) weighs approximately 50.0 kg (110.23
____
 lb).

 (5) Remove the girt bar (10) from the girt assembly (11): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN THE
_______
 PACK ASSEMBLY.

 (a)
 Pull open the burr-strips of the girt assembly (11).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(116)