25-62-48-991-003 Fig. 403
3. Job Set-up
__________ Subtask 25-62-48-861-050
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 25-62-48-860-051
B. Aircraft Maintenance Configuration
(1)
Put the access platform(s) in position at the applicable Emergency Exit Door(s).
(2)
Open the emergency exit door(s) from the passenger compartment (Ref. TASK 52-22-00-010-001) or from the outside (Ref. TASK 52-22-00-010-002).
(3)
Put the warning notice(s) on the Emergency Exit Door(s) to tell persons not to close the door(s).
Subtask 25-62-48-010-050
C. Get Access (Ref. Fig. 401/TASK 25-62-48-991-001, 402/TASK 25-62-48-991-002, 403/TASK 25-62-48-991-003)
(1)
Do the special precautions on the door damper and the emergency operation cylinder (Ref. TASK 52-22-00-860-003).
(2)
Install the SAFETY PIN - SLIDE RELEASE LEVER (27) in the related rigging hole of the lever (28).
(3)
Get access to the inflation reservoir(s): WARNING : BE CAREFUL WITH THE INFLATION RESERVOIR AND ITS COMPONENTS.
_______ THE RESERVOIR IS AN ALUMINUM BOTTLE WOUND IN KEVLAR FIBERS BONDED WITH EPOXY RESINS, AND IS PRESSURIZED WITH GAS. IF YOU CAUSE DAMAGE TO THE RESERVOIR, THERE IS A RISK OF EXPLOSION. NO DAMAGE IS PERMITTED.
INTENTIONALLY BLANK
R Emergency Escape-Slide Release-Mechanism Assembly Figure 401/TASK 25-62-48-991-001- 13 (SHEET 1)
EFF : 301-399, 25-62-48 Page 404 Nov 01/04
CES
R Emergency Escape-Slide Release-Mechanism Assembly Figure 401/TASK 25-62-48-991-001- 23 (SHEET 2)
EFF : 301-399, 25-62-48 Page 405 Nov 01/04
CES
R Emergency Escape-Slide Release-Mechanism Assembly Figure 401/TASK 25-62-48-991-001- 33 (SHEET 3)
EFF : 301-399, 25-62-48 Page 406 Nov 01/04
CES
INTENTIONALLY BLANK
Emergency Escape-Slide Release-Mechanism Assembly
Figure 402/TASK 25-62-48-991-002- 13 (SHEET 1)
CES
Emergency Escape-Slide Release-Mechanism Assembly
Figure 402/TASK 25-62-48-991-002- 23 (SHEET 2)
CES
Emergency Escape-Slide Release-Mechanism Assembly
Figure 402/TASK 25-62-48-991-002- 33 (SHEET 3)
CES
INTENTIONALLY BLANK
Emergency Escape-Slide Release-Mechanism Assembly
Figure 403/TASK 25-62-48-991-003- 13 (SHEET 1)
CES
Emergency Escape-Slide Release-Mechanism Assembly
Figure 403/TASK 25-62-48-991-003- 23 (SHEET 2)
CES
Emergency Escape-Slide Release-Mechanism Assembly
Figure 403/TASK 25-62-48-991-003- 33 (SHEET 3)
CES
(a)
Open the overhead-stowage compartment-door(s) (3) above the Emergency Exit Door(s).
(b)
Release the fasteners (2) and remove the inflation-reservoir access-panel (1) from the door frame-lining above the Emergency Exit Door.
NOTE : This step is only necessary when the LH FWD Emergency Exit
____
Door is also a Passenger/Crew Door.
(4) Install the lockpin assembly in the operating head of the inflation reservoir (Ref. TASK 25-62-49-000-001).
WARNING : MAKE SURE THAT THE LOCKPIN ASSEMBLY IS CORRECTLY INSTALLED
_______ IN THE VALVE/REGULATOR ASSEMBLY OF THE INFLATION RESERVOIR. IT PREVENTS AN ACCIDENTAL INFLATION OF THE ESCAPE SLIDE/SLIDE RAFT.
(5) Remove the door frame linings:
- of the LH FWD Emergency Exit Door, Zone 231 (Ref. TASK 25-23-47-000-004).
- of the RH FWD Emergency Exit Door, Zone 232 (Ref. TASK 25-23-47-000-009).
- of the LH AFT Emergency Exit Door, Zone 251 (Ref. TASK 25-23-47-000-010).
- of the RH AFT Emergency Exit Door, Zone 252 (Ref. TASK 25-23-47-000-010).
(6)
Install the RIGGING PIN - SLIDE RELEASE MECHANISM (55) in the related rigging hole of the lever assembly (54).
(7)
Install the RIGGING PIN - SLIDE RELEASE MECHANISM (44) in the related rigging hole of the release lever (43).
(8)
Remove the insulation blankets in the area that you are working. (Ref. TASK 25-80-00-000-001)
