(c)
Hold the override clutch (14) in position and align the punch marks on the shaft (16) and the override clutch (14).
(d)
Carefully push the shaft (16) through the opening of the override clutch (14) until you can see it at the other side of the opening.
(e)
Apply COMMON GREASE (Material No. 04-004) on the inside-surface of the sleeve (8).
(f)
Hold the sleeve (8) in position and carefully continue to push the shaft (16) through the sleeve (8) in the bearing-assembly (6).
(g)
Adjust the gap between the shaft (16) and the bearing-assembly
(6) (see detail E):
1_ Put the bearing-assembly (18) in position and install the
washers (21) and (24), and the screws (22) and (25).
NOTE : This step is neccessary to hold the shaft (16) in____
position.
2_ Measure the distance between the shaft (16) and the
bearing-assembly (6) with a feeler gage.
3_ Make sure that the gap is not less than 0.1 mm (0.0039 in.),
or more than 0.6 mm (0.0236 in.).
4_ If the distance between the shaft (16) and the
bearing-assembly (6) is not in this tolerance, you must adjust
the gap with the washer(s) (7):
washer AN960C616,
and/or
washer AN960C616L,
and/or
EFF : 301-399, 25-62-48Page 424
Nov 01/04
R
CES
washer AN960C616LL.
5_ Remove the screws (22) and (25), the washers (21) and (24),
and the bearing-assembly (18).
6_ Carefully pull the shaft (16) out of the bearing-assembly (6)
until you can install the washers (7) on the shaft (16).
7_ Carefully push the shaft (16) back in the bearing-assembly
(6).
(h)
Put the spring element (17) in the bearing-assembly (18).
(i)
Install the bearing assembly: WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______ SPECIAL MATERIAL. THIS MATERIAL IS DANGEROUS.
WARNING : YOU MUST ALWAYS WEAR RUBBER GLOVES WHEN YOU DO THIS
_______ PROCEDURE.
1 Apply SEALANTS (Material No. 09-019) on the mating surface of
_ the bearing-assembly (18).
2 Put the bearing-assembly (18) in position and install the
_ washers (21) and (24), and the screws (22) and (25).
(j)
Install the stop-screw (23).
(k)
Apply COMMON GREASE (Material No. 04-004) on the inside-surface of the sleeve (26).
(l)
Install the sleeve (26) and hold the lever (28) in position.
(m)
Hold the override clutch (14) in position and align the punch marks on the lever (28) and the shaft (16).
(n)
Install the lever (28), the washer (29) and the dome nut (30).
(o)
Install the SAFETY PIN - SLIDE RELEASE LEVER (27) in the related rigging hole of the lever (28).
(4) Install the release-mechanism rod-assembly (46) (refer to as the rod assembly):
(a) Apply COMMON GREASE (Material No. 04-004) on the pin (40).
EFF : 301-399, 25-62-48Page 425
Nov 01/04
R
CES
(b)
Put the eye-end of the rod assembly (46) in position at the release lever (43).
(c)
Install the pin (40), the washer (41) and the new cotter pin-corrosion resistant steel MS24665-151 (42).
(d)
Apply COMMON GREASE (Material No. 04-004) on the pin (48).
(e)
Put the other eye-end of the rod assembly (46) in position at the lever assembly (54).
(f)
Install the pin (48) the washer (49), and the new cotter pin-corrosion resistant steel MS24665-151 (50).
NOTE : If you cannot install the pin (48) easily, adjust the rod
____ assembly (46).
(g) Adjust the rod assembly:
1_ Cut, remove and discard the lock-wire from the lock-nuts (45)
and (47) on the rod assembly (46).
2_ Loosen the lock-nuts (45) and (47).
3_ Turn the eye-ends IN or OUT to adjust the rod assembly (46)
until you can easily install the pin (48).
4_ Tighten the lock-nuts (45) and (47).
5_ Safety the lock-nuts (45) and (47) with MISCELLANEOUS
(Material No. 19-010) (Ref. TASK 20-11-11-911-001).
6_ Make sure that the eye-ends of the rod assembly (46) are in
safety.
(5) Install the release-mechanism control-cable assembly (9) (refer to as the control cable):
(a)
Put the control cable (9) in position in the slots of the brackets (65) and tighten the lock-nuts (63) and (64) by hand.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(140)
