B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-060  USA MIL-T-4053 TAPE, PRESSURE SENSITIVE,GLASSCLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-50-00-200-002 General Visual Inspection of Cargo Compartment Decompression, Lining and Floor Panels 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
 Yellow Electric Pump R 25-54-12-991-006 Fig. 801 R 25-54-12-991-007 Fig. 802
 EFF : ALL
25-54-12Page 801

 3. Job Set-up
__________
 **ON A/C 001-049, 101-105,

 Subtask 25-54-12-010-055-A
 A. Get Access
 (1)
 Open the FWD cargo-compartment door and install the actuator safety lock (Ref. TASK 52-30-00-860-001).

 (2)
 Put the access platform in position at the opening of the FWD cargo-compartment door.

 (3)
 Put a warning notice in position on the control panel of the FWD cargo loading system (CLS) to tell persons not to use it.

R **ON A/C 051-099, 106-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 25-54-12-010-055
 A. Get Access
 (1)
 Open the FWD cargo-compartment door and install the actuator safety lock (Ref. TASK 52-30-00-860-001).

 (2)
 Put the access platform in position at the opening of the FWD cargo-compartment door.

 **ON A/C 001-049, 101-105,
 Subtask 25-54-12-865-065
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2000VU SEMI AUTO CLS-FWD 2MY B3 2000VU SEMI AUTO CLS-FWD 3MY B1
 EFF : ALL
25-54-12Page 802

 **ON A/C ALL
 4. Procedure_________ 
R  (Ref. Fig. 801/TASK 25-54-12-991-006, 802/TASK 25-54-12-991-007)
 Subtask 25-54-12-210-051
 A. Inspection
 (1) Do an inspection of the lining panels of the FWD cargo-compartment for missing fasteners (Ref. TASK 25-50-00-200-002).
R R R R  (2) Missing fasteners are permitted on the ceiling, sidewall and the partition lining panels if: - there are no fasteners (1) missing at the corners of the lining panels - not more than one fastener (2) is missing from an edge of a lining panel.
 Subtask 25-54-12-350-050
 B. Repair
 (1) If a stud is missing, install a new fastener assembly (stud, washer and lock washer).
R R R R  (2) If it is not possible to install the fastener(s) in the time necessary, seal the stud hole(s) (3) as follows: - seal the hole (3) on the lining panel where the fastener is missing with the Highspeed Tape (4) or the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-060) (4).
 NOTE : The edge where the fastener is missing must be sealed.____
 (3) Seal the edge where the fastener is missing as follows:
R R R R R R R  (a) If there is sufficient clearance between the panel with the missing fastener (3) and the adjacent panel: - make an overlap from the panel with the missing fastener (3) to the secondary structure (5) - do this with the Highspeed Tape (4) or the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-060) (4) - the tape (4) must extend to the next fasteners adjacent to the sealed hole (3).

 EFF : ALL
25-54-12Page 803
May 01/05

R R  Missing Fastener Inspection Figure 801/TASK 25-54-12-991-006
 EFF :  ALL  25-54-12 Page 804 May 01/05
 CES 

 INTENTIONALLY BLANK

R R  Missing Fastener Repair Figure 802/TASK 25-54-12-991-007- 12 (SHEET 1)
 EFF :  ALL  25-54-12 Page 806 May 01/05
 CES 

R R  Missing Fastener Repair Figure 802/TASK 25-54-12-991-007- 22 (SHEET 2)
 EFF :  ALL  25-54-12 Page 807 May 01/05
 CES 

 (b) If there is not sufficient clearance between the panel with the 
R  missing fastener (3) and the adjacent panel: 
R  - make an overlap from the panel with the missing fastener (3) to 
R  the next panel 
R  - do this with the Highspeed Tape (4) or the BONDING AND ADHESIVE 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(8)