1. At the Flight Attendant Panel (FAP) 120RH:
-If the display screen is blank, touch the screen surface.
-Select the Doors/Slides key (1).
At the FAP 120RH:
-
The CABIN STATUS page shows.
-
The DOORS/SLIDES page shows therelated EMER EXIT (L, R,) green.
EFF : ALL
25-62-46Page 421
Operational Test - Monitoring Figure 402A/TASK 25-62-46-991-003-A
R EFF : 106-149, 301-399, 401-499, 25-62-46 Page 422 Aug 01/05
CES
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
2. At the applicable inflation reservoir (5):
-Disconnect the related electrical connector (21) FOR 7506MM 7555VC-A, FOR 7507MM 7556VC-A.
3. At the FAP 120RH:
-Select the Doors/Slides key (1).
4. At the applicable inflation reservoir (5):
-Connect the related electrical connector (21) FOR 7506MM 7555VC-A, FOR 7507MM 7556VC-A.
5. At the FAP 120RH:
-Select the Doors/Slides key (1).
-
After approximately 3 minutes theDOORS/SLIDES page shows the related EMER EXIT (L, R) amber, and the message CHECK SLIDE PRESSURE.
-
After approximately 3 minutes theDOORS/SLIDES page shows the related EMER EXIT (L, R,) green.
**ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 25-62-46-410-050
A. Close Access
(Ref. Fig. 401/TASK 25-62-46-991-001)
(1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) FOR 7506MM
(a) Install the access panel 151CW or 151SW. R (3) FOR 7507MM
(a) Install the access panel 152CW or 152SW.
(4)
Set the AFT CARGO COMPT light switch 8LU to the OFF position.
(5)
Remove the access platform(s).
(6)
Close the AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
(7)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 25-62-46-862-050
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
EFF : ALL
25-62-46Page 424
SLIDE - ESCAPE, DOOR 2/3 (7770MM,7771MM,7772MM,7773MM) - REMOVAL/INSTALLATION
_____________________________________________________________________________ TASK 25-62-47-000-002 Escape-Slide - Removal after Inflation
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 2 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-62-47-000-001 Escape-Slide Enclosure - Removal 25-62-47-400-001 Escape-Slide Enclosure - Installation 25-62-49-000-001 Inflation Reservoir, Escape-Slide - Removal 25-62-49-400-001 Inflation Reservoir, Escape-Slide - Installation 52-22-00-860-002 Diaphragm Replacement at the Door Damper and
Emergency Operation Cylinder 25-62-47-991-002 Fig. 401
3. Job Set-up
__________ Subtask 25-62-47-860-050
A. Aircraft Maintenance Configuration
(1) Make sure that the EMER EXIT switch 4WL on the SIGNS panel 25VU is set to the OFF position (Ref. 23-73-00).
4. Procedure
_________ (Ref. Fig. 401/TASK 25-62-47-991-002) Subtask 25-62-47-020-053
A. Removal: NOTE : The removal procedures are given for the inflated slide assembly
____ at the left door 2; the procedures for inflated slides at the right door 2 and the left and right doors 3 are almost the same.
(1) At the top of the escape slide assembly, locate the quick release handle (1).
NOTE : The quick release handle (1) is protected by a soft flap cover
____ (2). The flap, placarded: 'FOR DITCHING USE ONLY. LIFT FLAP -PULL HANDLE', and the handle are held in position by velcro.
(2)
Lift the flap (2) and grip the quick release handle (1).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(131)
