(a) push in the flapper valves (1) of the aspirator (2) and release the pressure from the offwing escape slide (15).

 (2)
 Disconnect the offwing escape slide (15):

 (a)
 disconnect the inflation hose (3) from the stowage compartment union (4),

 (b)
 disconnect the electrical connectors (5) at the emergency
 lighting supply-cable,

 NOTE : Hold both ends of each connector with a finger and a
____ thumb. Turn one half of the connector a quarter turn (90 degrees) and pull the connector apart.
 (c)
 put blanking plugs on the disconnected line ends,

 (d)
 put blanking caps on the disconnected electrical connectors.

 (3)
 Detach the girt assemblies:

 (a)
 support the slide and release the LOWER girt assembly (6),

 (b)
 open the girt flap (9) and find the girt release handle (10),

 (c)
 remove the girt release handle (10) from the attach velcro (11),

 (d)
 pull the girt release handle (10) to remove the release pin (12),

 (e)
 let the lace-up joint (13) open to release the offwing
 escape-slide girt (14),

 (f)
 do step A.(2) again with the FWD girt assembly (7) and the TOP girt assembly (8).

 (4)
 Remove the deflated offwing escape slide: NOTE : Make sure the ground area, where the offwing escape slide (15)

____
 is lowered, is clean and free from sharp objects.

 (a) carefully lower the offwing escape slide (15) to the ground,
R  EFF : 001-049, 051-099, 101-149, 151-199, 25-62-42Page 403 201-299, 401-499, Aug 01/05
 CES

 Offwing Escape Slide - Inflated Figure 401/TASK 25-62-42-991-004- 12 (SHEET 1) 
R  EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,  25-62-42 Page 404 Aug 01/05
 CES 

 Offwing Escape Slide - Inflated Figure 401/TASK 25-62-42-991-004- 22 (SHEET 2) 
R  EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,  25-62-42 Page 405 Aug 01/05
 CES 

 (b) roll up the deflated offwing escape slide (15). NOTE : When you roll up a deflated escape slide (15), start from
____
 the bottom end of the slide.

 (5) Remove the escape slide enclosure, 193AT (194AT):
 (Ref. Fig. 402/TASK 25-62-42-991-005)

 (a)
 remove and retain the seal attach-plate screws (10) and the countersunk washers (11),

 (b)
 remove and retain the seal attach plate (12) and the seal strips (9),

 (c)
 loosen the esape slide enclosure studs (17),

 (d)
 move the top of the escape slide enclosure (7) outboard at an angle and hold it,

 (e)
 disconnect the emergency-lighting electrical connector (14),

 (f)
 disconnect the inflation hose (16) from the fuselage union (15), and remove the escape slide enclosure (7) from the aircraft.

 (g)
 put blanking plugs on the disconnected line ends,

 (h)
 put blanking caps on the disconnected electrical connectors. NOTE : Make sure that all related components (escape slide

____ enclosure (7) and attached enclosure door (8), seal attach plate (12), seal strips (9), screws (10), countersunk washers (11)), removed with the deflated escape slide are kept together. They are made to operate as a complete assembly.
 5. Close-up
________ Subtask 25-62-42-860-052
 A. Aircraft Maintenance Configuration
 (1)
 Remove the discharged inflation reservoir/s, 7506MM (7507MM) (Ref. TASK 25-62-46-000-001).

 (2)
 Install the charged inflation reservoir/s, 7506MM (7507MM) (Ref. TASK 25-62-46-400-001).

R  EFF : 001-049, 051-099, 101-149, 151-199, 25-62-42Page 406 201-299, 401-499, Aug 01/05
 CES

 (3) Install the offwing escape slide/s, 7504MM (7505MM) (Ref. TASK 25-62-
42-400-001).

R  EFF : 001-049, 051-099, 101-149, 151-199, 25-62-42Page 407 201-299, 401-499, Aug 01/05
 CES

 Offwing Escape-Slide Compartment 7504MM (7505MM) Figure 402/TASK 25-62-42-991-005- 13 (SHEET 1) 
R  EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,  25-62-42 Page 408 Aug 01/05
 CES 

 Offwing Escape-Slide Compartment 7504MM (7505MM) Figure 402/TASK 25-62-42-991-005- 23 (SHEET 2) 
R  EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,  25-62-42 Page 409 Aug 01/05
 CES 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(81)