CAUTION : MAKE SURE THAT THE PROTECTION IS CORRECLTY ATTACHED
_______ WITH TAPE TO THE AIRCRAFT STRUCTURE. THIS PREVENTS THE SUCTION OF LOOSE MATERIAL INTO THE ASPIRATOR DURING DEPLOYMENT. LOOSE MATERIAL CAN CAUSE DAMAGE TO THE ASPIRATOR.
(d)
Refer to the FIGURE for the approximate dimensions and position of the protection.
(e)
Use tacky tape SPECIAL MATERIALS (Material No. 05-069) and attach the protection on to the upper surface of the wing.
(2) Ground safety procedure:
WARNING : PUT SAFETY BARRIERS IN POSITION TO KEEP THE TRAVEL RANGE OF
_______ THE OFFWING ESCAPE-SLIDE CLEAR. IF YOU DO NOT, INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT CAN OCCUR.
(a)
Below the related offwing escape-slide, make sure that an area with approximately 12.0 m (39.37 ft.) radius is clear of all miscellaneous equipment.
(b)
Put the safety barriers in position.
(c)
Put plastic sheet in position where the offwing escape-slide hits the ground.
(d)
Put WARNING NOTICE in position to tell persons not to go into the area behind the safety barriers.
(3) Cockpit safety procedure:
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
(a)
Set the slat/flap control lever to the 0 position (Ref. TASK 27-50-00-866-009).
(b)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the slat/flap control lever when working near the slats/flaps.
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-00Page 209 201-299, 401-499, Aug 01/05
CES
(c) Put the WARNING NOTICE on the slat/flap control lever to tell persons not to operate the flaps.
4. Procedure
_________
Subtask 25-62-00-820-050
A. Adjustment Procedure
(Ref. Fig. 202/TASK 25-62-00-991-004)
R (1) FOR 7507MM CAUTION : MAKE SURE THAT THE AFT CARGO-COMPARTMENT DOOR IS CLOSED
_______ BEFORE THE RIGHT OFFWING ESCAPE-SLIDE DEPLOYS. IF THE DOOR IS NOT CLOSED, YOU CAN CAUSE DAMAGE TO:
-
THE INFLATABLE ASSEMBLY
-
THE AFT CARGO-COMPARTMENT DOOR.
(a)
Remove the access platform(s).
(b)
Close the AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
NOTE : You must close the AFT cargo-compartment door to prevent
____ damage to the offwing escape-slide if an accidental inflation occurs.
(c) Use a MIRROR - INSPECTION, FLEXIBLE to let you see the pulley stop-pin (6) on the right regulator valve assembly (5).
(2)
Remove the lock pin (3) from the pocket (1).
(3)
Adjustment procedure of the regulator valve assembly:
WARNING : MAKE SURE THAT YOU TURN THE PULLEY STOP-PIN ONLY IN THE
_______ DIRECTION OF THE BLACK MARK (CLOSED POSITION). IF YOU TURN THE PULLEY STOP-PIN IN THE OPPOSITE DIRECTION, YOU WILL START AN UNWANTED DEPLOYMENT SEQUENCE. THIS CAN CAUSE INJURY TO PERSONNEL AND DAMAGE TO EQUIPMENT.
(a)
Put an ALLEN KEY 3/16 IN (8) into the hexagonal socket (9).
(b)
Turn the Allen key (8) in the SAFE direction, to move the pulley stop-pin (6) in the direction of the BLACK mark (7) (closed position).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-00Page 210 201-299, 401-499, Aug 01/05
CES
Inflation Reservoir - Adjustment Procedure to Install the Lock Pin Assembly Figure 202/TASK 25-62-00-991-004
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-00Page 211 201-299, 401-499, Aug 01/05
CES NOTE : When the pulley stop-pin (6) is in the fully closed
____ position, the internal hole aligns with the installation hole (4).
(4) Install the lock pin (3) in the installation hole (4). R (5) FOR 7507MM
(a)
Open the AFT cargo-compartment door (Ref. TASK 52-30-00-860-001).
(b)
Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE back in position adjacent to the AFT cargo-compartment exit.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(64)
