2 Put the lever (132) and (137) together with the bush (134) in
_
position on the shaft (135).
3 Install the bolt (131) and the nut (138).
_
4_ Put the washers (139) in position on the shaft (135).
5_ Apply COMMON GREASE (Material No. 04-004) to the torsion spring (140).
6_ Put the torsion spring (140) in position on the camshaft (135)
7_ Make sure that the spring-end of the torsion spring (140) is engaged in the related locating-hole of the lever (137).
8_ Install the lever (142):
WARNING : BE CAREFUL WHEN YOU INSTALL THE LEVER ON THE_______ CAMSHAFT AND CONNECT IT TO THE TORSION-SPRING. THE TENSION OF THE TORSION-SPRING CAN CAUSE SUDDEN MOVEMENT OF THE LEVER. THIS CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT.
a_ Apply COMMON GREASE (Material No. 04-004) to the splines of the camshaft (135) and the lever (142).
b_ Apply a force on the spring-end of the torsion spring (140) and adjust a pre-tension to between 0.875 and 1.049 m.daN (77.43 and 92.83 lbf.in)
c_ Install the lever (142) on the camshaft (135).
NOTE : The punch mark "G" on the lever (142) must align____ with the punch mark "H" on the camshaft (135).
d_ Make sure that the spring-end of the torsion spring (140) is engaged in the related locating-hole of the lever (142).
e_ If the pre-tension of the torsion spring (140) is not in the limits to between 0.875 and 1.049 m.daN (77.43 and 92.83 lbf.in) you can adjust the pre-tension with the lever (142).
NOTE : It is permitted to install the lever (142) one____ spline next to the related punch marks "G" and "H".
f_ Install the bolt (141) and the nut (143).
9_ Apply COMMON GREASE (Material No. 04-004) to the inner splines of the camshaft (135) and on the splines in the middle of the shaft (130).
Adjustments Figure 409/TASK 25-62-43-991-008- 14 (SHEET 1)
R EFF : 001-049, 051-099, 101-149, 201-299, 25-62-43 Page 464 May 01/05
CES
Adjustments Figure 409/TASK 25-62-43-991-008- 24 (SHEET 2)
R EFF : 001-049, 051-099, 101-149, 201-299, 25-62-43 Page 465 May 01/05
CES
Adjustments Figure 409/TASK 25-62-43-991-008- 34 (SHEET 3)
R EFF : 001-049, 051-099, 101-149, 201-299, 25-62-43 Page 466 May 01/05
CES
Adjustments Figure 409/TASK 25-62-43-991-008- 44 (SHEET 4)
R EFF : 001-049, 051-099, 101-149, 201-299, 25-62-43 Page 467 May 01/05
CES
10__ Carefully push the shaft (130) through the opening of the
camshaft (135) until you can align the two punch marks "E" and
"F".
11 Align the two punch marks "E" and "F" and continue to push the
__ shaft (130) into the camshaft (135).
12 Install the bush (144).
__
(b) Install the camshaft assembly: NOTE : You will find punch marks on the shaft-ends of the
____ camshaft assembly (121), and on the levers (113) and (127) to make the assembly easier.
1 Apply COMMON GREASE (Material No. 04-004) to the shaft-end
_ splines of the camshaft assembly (121).
2 Apply SEALANTS (Material No. 09-019) to the mating surfaces of
_ the bearing flanges (118) and (124).
3 Put the bearing flanges (118) and (124) in position on the
_ shaft-ends of the camshaft assembly (121).
4 Put the camshaft assembly (121) in position.
_ 5 Apply SPECIAL MATERIALS (Material No. 05-002) to the threads
_ of the bolts (116) and (123), and on the thread of the stop-screw (115).
6 Put the bearing flange (124) in position on the frame
_ structure.
7 Install the bolts (123) and the nuts (122).
_ 8 Put the bearing flange (118) in position on the frame
_ structure.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(99)
