(1)
Apply SEALANTS (Material No. 09-018) to the mating surface of the hinge assemblies (5).
(2)
Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the screws (4).
Subtask 52-41-16-420-050
C. Installation of the Access Door
(1)
Put the access door (6) in its installation position.
(2)
Install the washers (2), the screws (4) and the nuts (1).
(3)
Attach the bonding strap (12) with the washers (10), the screw (11) and the nut (9) on the access door (6) (Ref. TASK 20-28-00-912-004).
5. Close-up
________ Subtask 52-41-16-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply a layer of SPECIAL MATERIALS (Material No. 05-027) (Ref. TASK 51-75-13-916-001).
(3)
Close the access door (6).
(4)
Remove the access platform(s).
1EFF : ALL 1 52-41-16Page 406 1 1 Feb 01/98 1 1 1CES 1
ACCESS FAIRING - APU EXHAUST - REMOVAL/INSTALLATION
___________________________________________________ TASK 52-41-18-000-001 Removal of the APU Exhaust Access-Fairing 317AL WARNING : MAKE SURE THAT THE EXHAUST MUFFLER IS SUFFICIENTLY COOL BEFORE YOU
_______ REMOVE THE EXHAUST ACCESS FAIRING OF THE APU. THIS WILL PREVENT BURNS.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform(s) 5.0 m (16 ft. 5 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-41-15-000-001 Removal of the Tail Navigation Light 15LA 33-48-13-000-001 Removal of the Tail Cone Strobe-Light (19LV) 52-41-18-991-001 Fig. 401
3. Job Set-up
__________ Subtask 52-41-18-860-050
A. Aircraft Maintenance Configuration
(1)
Put the warning notice in the flight compartment to tell persons not to start the APU.
(2)
Put the access platform(s) in position below the tail cone.
1EFF : ALL 1 52-41-18Page 401 1 1 Feb 01/98 1 1 1CES 11EFF : ALL 1 52-41-18Page 402 1 1 May 01/05 1 1 1CES 1
Subtask 52-41-18-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41 122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03
4. Procedure_________
(Ref. Fig. 401/TASK 52-41-18-991-001)
Subtask 52-41-18-020-050
R A. Removal of the APU Exhaust Access-Fairing 317AL
NOTE : In the subsequent procedure the APU exhaust access-fairing 317AL____ is referred to as fairing.
R (1) Release the five stud nuts (2) and carefully remove the fairing (1) from the tail cone (11).
R R R R R (2) Hold the fairing (1) and disconnect the electrical connectors (3) and (4) from the tail navigation light 15LA and the tail cone strobe-light 19LV.
R (3) Put blanking caps on the disconnected electrical connectors.
R (4) Remove the screw (6), the washer (7) and the nut (9) and disconnect the bonding strap (8) from the fairing (1).
R (5) If necessary, remove the tail navigation light 15LA (Ref. TASK 33-41-15-000-001).
R R (6) If necessary, remove the tail cone strobe-light 19LV (Ref. TASK 33-48-13-000-001).
R APU Exhaust Access-Fairing 317AL Figure 401/TASK 52-41-18-991-001
1EFF : 1 1 1CES ALL 1 111 52-41-18 Page 403 May 01/05
TASK 52-41-18-400-001
Installation of the APU Exhaust Access-Fairing 317AL
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(154)
