NOTE : The location of the claws make sure that you can move the
____ Bulk door freely from or into the closed position.
(c) Measure the clearance between the stop screw (38) of the limit stop (36) and the support screw (39) of the support fitting (40).
NOTE : Both screws must have contact.
____
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 529 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(d)
If not, add the same quantity of washers (37) at the stop screw
(38) and at the support screw (39) as follows:
(e)
Make sure that the stop screw (38) has contact with the support screw (39).
(f)
If not, do the above adjustment again until the two screws have contact.
1_ Move the door handle to the LOCKED position.
2_ Remove the nuts (35) from the limit stop (36).
3_ Remove the stop screw (38) from the limit stop (36).
4_ Remove the support screw (39) from the support fitting (39).
5_ Install the same quantity of washers (37) at the support screw
(39) and at the stop screw (38) as necessary.
6_ Install the stop screw (38) with the related washers (37) on
the limit stop (36).
7_ Install the support screw (39) with the related washers (37)
on the support fitting (39).
8_ Install the nuts (35) on the support screw (39) and on the
stop screw (38) and tighten them.
9_ Move the door handle to the OPEN position.
Subtask 52-33-11-820-053
B. Adjustment of the Gaps
(1) Measure the gaps "J" and "K" between the forward latch spigot and the forward barrel lock (20).
NOTE : The gap "J" must be a minimum of 0.1 mm (0.0039 in.). The gap
____ "K" must be between 0.5 mm (0.0196 in.) and 1.0 mm (0.0393 in.).
(2) Measure the gaps "L" and "M" between the aft latch spigot and the aft barrel lock (20).
NOTE : The gap "L" must be a minimum of 0.1 mm (0.0039 in.). The gap
____ "M" must be between zero and 0.5 mm (0.0196 in.).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 530 1224-224, 228-228, 1May 01/05 1 1 1CES 1 (3) Adjust the gaps "K" and "M" as follows:
(a)
Open the Bulk door to get access to the forward and aft barrel locks (20).
(b)
Safety the not fully opened Bulk door with an applicable support device.
(c)
Remove the nuts (23), the washer (24) and the bolts (25) from the shaft (22).
(d)
Pull the forward and aft barrel locks (20) together with the spacer set (21) away from the shaft (22).
(e)
Add or remove one spacer to change the thickness of the spacer set (21) as required.
NOTE : Obey the preparation instructions of the subsequent
____ components (Ref. TASK 52-33-21-400-001).
(f)
Install the forward and aft barrel locks (20) together with the spacer set (21) into the shaft (22).
(g)
Connect the shaft (22) to the forward and aft barrel locks (20) as follows:
1_ Remove the nuts (27), the washers (28) and the bolts (29) to
disconnect the flange (26) from the joint assembly (30).
2_ Align the holes of the forward and aft barrel locks (20) and
the shaft (22).
3_ Install the bolt (25) with the washers (24) and the nuts (23).
4_ Connect the flange (26) with the joint assembly (30) and
install the bolts (29), the washer (28) and the nuts (27).
NOTE : Make sure that the mating surfaces of the flange (26)____
and the joint assembly (30) have contact and their
holes align.
5_ If necessary, turn the flange (26) to get contact to the
mating surfaces and/or to align the holes.
6_ Tighten the nuts (27),(23).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 531 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(h)
Remove the support device and set the Bulk door in the locked position.
(i)
Make sure that the gaps "K" and "M" are correct.
(4) Change the position of the forward and aft latch spigots on the door frame to adjust the gaps "J" and "L" correctly (Ref. TASK 52-33-32-400-001).
Subtask 52-33-11-860-054
C. Preparation for the Test
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Set the Bulk door in the correct closed position.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(38)
