(2)
 Remove the sealant from the stop fitting (2) and the bulk door frame with CLEANING AGENTS (Material No. 11-016) and a wooden or plastic scraper.

 (3)
 Clean the component interface and/or the adjacent area.

 (4)
 Apply SPECIAL MATERIALS (Material No. 05-002) to all bolts which attach the different components.

 (5)
 Apply SEALANTS (Material No. 09-005) to the mating surface of the stop fitting (2).

 Subtask 52-33-32-420-054
 B. Installation of the Door Frame Fittings
 (1) Install the stop fitting (2) as follows:
 (a) Attach the stop fitting (2) with the bolts (4),(5), the washers
 (3) and the nuts (1) at the bulk door frame.
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-32Page 409 1224-224, 228-228, 1May 01/05 1 1 1CES 1

 (b) TORQUE the nut (1) to between 0.70 and 0.80 m.daN (61.94 and
 70.79 lbf.in).
 (2) Install the forward latch spigot (18) as follows:
 (a)
 Put the serrated plate (13) and the forward latch spigot (18) in position on the serrated plate (12) of the bulk door frame. Make sure that the notches of these components are aligned.

 (b)
 Attach the forward latch spigot (18) with the bolts (15),(16), the washers (14),(17) and the nuts (11),(10) at the bulk door frame.

 NOTE : Do not torque the nuts at this stage.
____
 (3) Install the aft latch spigot (27) with the related Proximity switch 50WV as follows:
 (a)
 Put the serrated plate (31) and the aft latch spigot (27) in position on the serrated plate (30) of the bulk door frame.

 (b)
 Make sure that the notches of these components are aligned.

 (c)
 Attach the aft latch spigot (27) with the bolts (33),(37), the washers (32),(38) and the nuts (29),(28) at the bulk door frame.

 NOTE : Do not torque the nuts at this stage.
____
 (4) If required, assemble the proximity target (36) to the lever of the aft latch spigot (27) as follows:
 (a)
 Turn the proximity target (36) until the clearance between the target plate and the surface of the lever is 2.5 mm (0.0984 in.) (Pre-set measurement).

 (b)
 Install the new tab washer (34) and the nut (35) to the proximity target (36).

 NOTE : Do not safety the nut (35) with the new tab washer (34) at
____
 this stage.

R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-32Page 410 1224-224, 228-228, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-105,

 Subtask 52-33-32-820-054
 C. Adjustment Procedure
 (1)
 Carefully close the Bulk cargo-compartment door (Ref. TASK 52-30-00-860-008).

 (2)
 Make sure that the skin offset between the Bulk cargo-compartment door and the fuselage contour is correct (Ref. TASK 52-33-11-820-001).

 (3)
 Make sure that the Bulk cargo-compartment door closes easily.

 (4)
 Adjust the position of the forward and/or aft latch spigot as follows:

 (a) Measure the clearance Z between the barrel locks of the locking mechanism and the latch spigot.
 NOTE : The clearance Z must be min. 0.10 mm (0.0039 in.) .
____
 (b)
 If the clearance Z is not correct, adjust the position of the latch spigot with the related serrated plate (Ref. TASK 52-33-11-820-001).

 (c)
 TORQUE the nuts (10) and (28) to between 0.35 and 0.45 m.daN

 (30.97 and 39.82 lbf.in).

 (d)
 TORQUE the nuts (11) and (29) to between 0.70 and 0.80 m.daN

 (61.94 and 70.79 lbf.in).
 (5) Adjust the proximity switch 50WV as follows:
 (a) Measure the distance X between the target plate and bracket surface.
 NOTE : The distance X must be between 44.2 mm (1.7401 in.) and
____ 44.8 mm (1.7637 in.).
 (b)
 If the distance X is not correct, loosen the nut (35) and adjust the proximity target (36) until the distance is correct.

 (c)
 Tighten the nut (35) and safety it with the new tab washer (34).

R 1EFF : 001-049, 051-099, 101-105, 1 52-33-32Page 411 1 1 May 01/05 1 1 1CES 1

 (d)
 Install the proximity sensor (25) with the safety washer (23) and the nut (24) to the bracket of the aft latch spigot (27).

 (e)
 Safety the nut (24) and the safety washer (23) with lockwire, corrosion-resistant steel dia 0.6 mm (0.2362 in.).

 (f)
 Connect the connector of the cable loom (26) to the proximity sensor (25).

 (6) Do an operational test to make sure that the function of the proximity switch 50WV is correct (Ref. TASK 52-71-00-710-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(75)