-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-005 USA MIL-C-16173 GRADE II
Material No. 05-027 CORROSION PREVENTIVE (Ref. 20-31-00)USA MIL-L-81309
Material No. 11-002 RUST INHIBITOR(FOR CORROSION USE 15-004) (Ref. 20-31-00)USA MIL-PRF-680
Material No. 11-004 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)USA MIL-T-81533
Material No. 13-002 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)USA MIL-C-5541 MIL-C-81706 CLASS I/A CHEMICAL CONVERSION COATING YELLOW ALUMINUM
Material No. 16-002 (Ref. 20-31-00)GB BAEP 3536
Material No. 16-006 POLYURETHANE TOPCOAT GREY (FOR INTERNAL APPLIC.) (Ref. 20-31-00)
Material No. 19-004 ANTI-CORROSION PRIMER (EPOXY-IMPRVD ADHESION) (Ref. 20-31-00)
WHITE TALCUM POWDER (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump
52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump
52-30-00-860-006 Open the Bulk Cargo-Compartment Door
52-30-00-860-008 Close the Bulk Cargo-Compartment Door
52-33-13-000-001 Removal of the Lining and Insulation of the Bulk
Cargo-Compartment Door
52-33-13-400-001 Installation of the Lining and Insulation of the Bulk
Cargo-Compartment Door
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 702 1224-224, 228-228, 1May 01/05 1 1 1CES 1
3. Job Set-up
__________ Subtask 52-33-11-010-062
A. Get Access
(1)
Open the AFT cargo-compartment door (Ref. TASK 52-30-00-860-001) to get access to the inner side of the Bulk cargo compartment door (referred to as Bulk door).
(2)
Remove the divider net between the AFT/Bulk cargo compartment at FR59.
(3)
Remove the door net from the opening of the Bulk door.
(4)
Remove the lining and the insulation from the Bulk door (Ref. TASK 52-33-13-000-001).
(5)
Put the access platform in position of the Bulk door.
(6)
Open the Bulk door (Ref. TASK 52-30-00-860-006) to clean the lateral components.
4. Procedure
_________ Subtask 52-33-11-160-050
A. Cleaning of the Structure of the Bulk Door
(1)
Remove all dirt or unwanted material with a vacuum cleaner and/or a dry brush.
(2)
Clean the painted components of the primary structure of the Bulk door with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth or a brush.
NOTE : Make sure that the cleaning agent does not dry on the surface.
____
(3) Clean the inner surface of the outer skin with CLEANING AGENTS (Material No. 11-002) to remove the remaining adhesive of the insulation panels.
NOTE : Make sure that the cleaning agent does not dry on the surface.
____
(4) Dry the cleaned components with a dry and clean lint-free cloth or with dry, compressed air.
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 703 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(5)
Examine the drain holes and the drain device to make sure that they are clean and not blocked.
(6)
Make sure that the corners and the recesses are clean of all unwanted material.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(47)
