3. Job Set-up__________
 Subtask 53-51-00-010-066
 A. Get Access 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION_______ 
R  BEFORE YOU START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL_______ 
R  MATERIAL. 
R  THIS MATERIAL IS DANGEROUS. 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ 
R  MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Put the access platform in position below the access door 312AR. 
R
 (2) Open the access door 312AR.
 (3) Get access to the inspection area.
 (4) Carefully clean the inspection area with CLEANING AGENTS (Material
 No. 11-004) and a lint-free cloth. 
R

 EFF : ALL
53-51-00Page 635
Feb 01/99

 4. Procedure
_________
 (Ref. Fig. 609/TASK 53-51-00-991-011) Subtask 53-51-00-210-064
 A. Inspection:
 (1) Examine the internal fin to fuselage attachment fittings for:
 -cracks,

 -loose or missing rivets,

 -distortion.
 NOTE : If necessary, refer to the ASRM (Ref. ASRM 535600000) for the

____
 correct repair procedure.

 5. Close-up
________ Subtask 53-51-00-916-054
 A. Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to the inspection area (Ref. TASK 51-75-13-916-001).
 Subtask 53-51-00-410-064
 B. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the access door 312AR.

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 EFF : ALL
53-51-00Page 636

 Internal Fin to Fuselage Attachment Fittings at FR72 and FR74
 Figure 609/TASK 53-51-00-991-011

 EFF : ALL
53-51-00Page 637

Feb 01/98
 CES  TASK 53-51-00-210-011

 Detailed Visual Inspection of Attach Fittings for Horizontal Stabilizer Trim Actuator at FR73
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 535161-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth
 No specific access platform 3 m (9 ft. 10 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 11-002  USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
 Material No. 15-005  AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-13-916-001 Repair to a layer of Moisture-Removing Oil
 ASRM 535129 (for corrective action)
 53-51-00-991-012 Fig. 610

 EFF : ALL
53-51-00Page 638

 3. Job Set-up
__________
 Subtask 53-51-00-010-067
 A. Get Access
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
 BEFORE YOU START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(107)