(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Protectice treatment.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
EFF : ALL
53-53-11Page 407
(a) Apply SPECIAL MATERIALS (Material No. 05-002) to the bolts (9), the bushes (6) and (7).
Subtask 53-53-11-420-050
B. Installation:
(1)
Install the bushes (6) and (7).
(2)
Put the support strut (1) in position and install the washers (8) and the bolts (9).
(3)
Install the washers (10) and the nuts (12).
(4)
TORQUE the nuts (12) to between 2.0 and 2.2 m.daN (14.74 and 16.22 lbf.ft).
(5)
Safety the nuts (12) with the new cotter pins (11).
(6)
Put the bonding straps in position and install the screws (2), the washers (3) and the nuts (5) (Ref. TASK 20-28-00-912-004).
(7)
Apply STORAGE PRESERVATION (Material No. 15-007) to the work area (Ref. TASK 51-75-13-916-002).
5. Close-up
________
(Ref. Fig. 401/TASK 53-53-11-991-001) Subtask 53-53-11-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 20CE1, 20CE2, 21CE1, 21CE2, 21CE3, 22CE.
Subtask 53-53-11-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access doors 312AR and 314AR.
(3)
Remove the warning notice(s).
EFF : ALL
53-53-11Page 408
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-53-11Page 409
TASK 53-53-11-000-002
Removal of the Diagonal Support Struts at STA3655/FR77
NOTE : The removal of one support strut is given. The procedure is the same for
____ the other support struts.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 2.5 m (8 ft. 2 in.)
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-41-00-220-003 Check of the Zero Adjustment of the THS 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 53-55-13-000-001 Removal of the Fairings at the THS Fittings. 55-15-11-000-001 Removal of the Apron 333AT/333AB/343AT/343AB 53-53-11-991-002 Fig. 402
EFF : ALL
53-53-11Page 410
3. Job Set-up
__________ Subtask 53-53-11-010-051
A. Get Access
(1)
Make sure that the Trimmable Horizontal Stabilizer (THS) is in the zero position (Ref. TASK 27-41-00-220-003).
(2)
Put the warning notice in position to tell persons not to operate the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
- 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(121)
