(b)
Attach the SLING - R/I TAILCONE to the crane.
(c)
Attach the sling to the hoisting lugs on the tail cone.
(d)
Lift the tail cone into position. NOTE : Make sure that the tail cone bearing (67) aligns with the
____
fuselage spigot (66).
(e)
Remove the installation adaptors (77) from the EXTRACTOR - ATTACH BOLTS, TAIL CONE (98A53407566005) kit and install the adaptors on the attach bolts (70).
NOTE : The tool kit with the partnumber 98A53407566005 supersedes
____ the tool kit with the partnumber 98A53407566002. If only the tool kit with the partnumber 98A53407566002 is available, then it is recommended to continue to use this tool kit.
(f)
Apply COMMON GREASE (Material No. 04-004) to the attach bolts (70).
(g)
Install the attach bolts (70) in the upper attach fittings.
(h)
Remove the installation adaptors from the upper attach bolts (70) and install the nuts (72).
(i)
Install the attach bolts (70) in the lower attach fittings.
(j)
Remove the installation adaptors from the lower attach bolts (70) and install the nuts (72).
(k)
TORQUE the nuts (72) to between 0.57 and 0.79 m.daN (50.44 and
69.91 lbf.in).
(l)
Safety the nuts (72) with the new cotter pins (73).
(m)
Apply STORAGE PRESERVATION (Material No. 15-007) to the exposed thread of the bolts. (Ref. TASK 51-75-13-916-002)
(n)
Protective treatment
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER
_______ SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
-Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (68).
(o) Put the access covers (69) in position and install and tighten the screws (68).
EFF : 001-049, 051-099, 101-105, 151-199, 53-58-11Page 438 201-210, Aug 01/05 R CES
(p)
Put the bonding straps (71) in position and install and tighten the nuts (74), bolts (75) and the washers (76) (Ref. TASK 20-28-00-912-004).
(q)
Disconnect the hoisting sling from the hoisting lugs.
(r)
Protective treatment.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER
_______ SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
-Remove the hoisting lugs from the tail cone and apply SPECIAL MATERIALS (Material No. 05-002) to the lugs.
(s)
Install the hoisting lugs in the hoisting points eye end in.
(t)
Install the SPECIAL MATERIALS (Material No. 05-052) over the hoisting points.
(2) Connect the APU fuel line: (Ref. Fig. 405/TASK 53-58-11-991-011)
(a)
Apply COMMON GREASE (Material No. 04-012) to the new O-rings (51) and install them on the shrouds (38) and (33).
(b)
Install the shroud (38) with the sleeve (54) over the fuel hose (37).
(c)
Remove the SLIDE CONE - APU FUEL and connect the nut (35) to the fitting (36).
(d)
Tighten the nut (35) (Ref. TASK 20-21-12-911-001) and safety with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
(e)
Install the shroud (38) in the sleeve (54) and slide the sleeve
(54) over the shroud (38) and the shroud (33).
(f)
Install the retaining springs (34) and safety with corrosion-resistant steel lockwire 0.6 mm (0.0236 in.) dia.
R EFF : 001-049, 051-099, 101-105, 151-199, 53-58-11Page 439 201-210, Aug 01/05
CES
(g)
Align the shroud (38) with the sleeve (54) and the shroud (33) and install the clamp (52).
(h)
Put the bonding straps (32), (46) and (53) in position and install and tighten the bolts (43), the washers (44) and the nuts
(49) (Ref. TASK 20-28-00-912-004).
(3)
Install the APU air-intake flap (Ref. TASK 49-16-43-400-001).
(4)
Connect the ball-bearing control cable to the APU air intake flap diverter (Ref. TASK 49-16-41-400-001).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(146)
