_
3 Remove the bush (15) and the bolt (16).
_
(2)
Pull the Y-bolt (17) out of the sleeve (18).
(3)
Install the DISTANCE STRUT - FRAME 77 (98D27408406000) as follows:
(a)
Put the distance struts in position between the left and the right upper and lower cross beam sections at FR77.
(b)
Install the struts to the cross beam sections.
(c)
Attach the adapter to the horizontal stabilizer and to the distance strut.
NOTE : Make sure the sleeve (18) is not loaded, turn the movable
____ spindle unit to make any necessary adjustments.
(4)
Install the EXTRACTOR - CENTERING BUSH, THS (98D27407505000) and remove the sleeve (18).
(5)
Remove and discard the O-rings (31).
(6)
Disconnect the lower floating bearing as follows:
(a)
Open the closed edges of the lockwasher (2) and the tabwasher (7).
(b)
Remove the nut (1) and remove and discard the lockwasher (2).
(c)
Remove the cup washer (22).
(d)
Remove the bolt (5).
(e)
Remove the nut (30), the screw (28) and the washers (29).
(f)
Remove the bonding jumper (27).
(g)
Remove and discard the cotter pin (12).
(h)
Remove the nut (9) and the washer (11).
(i)
Remove and discard the tabwasher (7).
(j)
Remove the retaining ring (3) and the sleeve (6).
(k)
Remove the bushes (4).
(7)
Disconnect the upper fixed bearing as follows:
(a)
Open the closed edges of the lockwasher (2) and the tabwasher (7).
(b)
Remove the nut (1) and remove and discard the lockwasher (2).
(c)
Remove the cupwasher (22).
(d)
Remove the bolt (5).
(e)
Remove the nut (30), the screw (28) and the washers (29).
(f)
Remove the bonding jumper (27).
(g)
Remove and discard the cotter pin (12).
(h)
Remove the nut (9) and the washer (11).
(i)
Remove and discard the tabwasher (7).
(j)
Remove the retaining ring (3) and the washer (21).
(k)
Carefully pull the sleeve (6) out of the link assembly and remove the bushes (20) and the washer (21).
(8)
Remove the spacer (13) as follows:
(a)
Remove and discard the cotter pin (26).
(b)
Remove the nut (25), the bolt (24) and the washers (10).
(c)
Remove the spacer (13).
(9)
Remove the links (19) and (23).
(10) Remove the bolts (8) from the link (19). R **ON A/C 004-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 53-56-11-020-050-A
A. Removal:
(1)
Remove and discard the cotter pin (43).
(2)
Remove the locking cap (42), the nut (41) and the washers (40), (44).
(3)
Remove the bush (15) and the bolt (16).
(4)
Pull the Y-bolt (17) out of the sleeve (18).
(5)
Install the DISTANCE STRUT - FRAME 77 (98D27408406000) as follows:
(a)
Put the distance struts in position between the left and the right upper and lower cross beam sections at FR77.
(b)
Install the struts to the cross beam sections.
(c)
Attach the adapter to the horizontal stabilizer and to the distance strut.
NOTE : Make sure the sleeve (18) is not loaded, turn the movable
____ spindle unit to make any necessary adjustments.
(6) Install the EXTRACTOR - CENTERING BUSH, THS (98D27407505000) and remove the sleeve (18).
EFF : ALL
53-56-11Page 410
(7)
Remove and discard the O-rings (31).
(8)
Disconnect the lower floating bearing as follows:
(a)
Open the closed edges of the lockwasher (2) and the tabwasher (7).
(b)
Remove the nut (1) and remove and discard the lockwasher (2).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(132)
