Aug 01/05
R
CES
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R ASRM 51-11-00-001 ASRM 51-22-00-001 ASRM 51-73-00-001 ASRM 51-74-00-001 NTM 53-41-45 P.B. 601 ASRM 53-00-12-201 51-73-11-300-003 51-74-11-300-001 53-41-00-991-039 (for corrective action) Repair of Dents in Skin Panels (for corrective action) Repair of Corroded Areas (for corrective action)Fig. 630
3. Job Set-up__________
Subtask 53-41-00-010-124
A. Get Access
(1) Put the warning notice in position to tell persons not to operate the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION_______ BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
(2) Put the access platform in position adjacent to FR47.5 LH and RH.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(3)
If necessary, clean the surfaces of the inspection area with CLEANING AGENTS (Material No. 11-004) and a MISCELLANEOUS (Material No. 19-003).
(4)
Make sure that the inspection areas are clean and dry before you continue.
(5)
Do a visual inspection of the surfaces of the inspection areas. Look for damage and defects in the shape of the surfaces.
(6)
If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001)for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-Refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage.
EFF : 301-399, 53-41-00Page C639
Aug 01/05
R
CES
4. Procedure
_________
(Ref. Fig. 630/TASK 53-41-00-991-039)
Subtask 53-41-00-220-060
A. Inspection
R R (1) Do a nondestructive test of the skin splice at FR47.5 from stringer 16 LH and RH to the crown center line (Ref. NTM 53-41-45 P.B. 601).
R (2) Record the damage that you find during the inspection procedure.
(3) If you find damage:
R R (a) Refer to the AMM for the classification of the damage (Ref. TASK 51-73-11-300-003).
R R R (b) If you find corrosion damage: - refer to the ASRM for the general corrosion data (Ref. ASRM 51-22-00-001) - refer to the AMM for the repair of the corroded areas (Ref. TASK 51-74-11-300-001).
R R (c) If you find other types of damage: - Refer to the ASRM for the repair of the minor damage (Ref. ASRM 51-73-00-001).
R R (d) If necessary, refer to the ASRM for the correct repair procedure (Ref. ASRM 53-00-12-201).
5. Close-up________
Subtask 53-41-00-410-122
A. Close Access
(1) Remove the access platform(s).
(2) Remove the warning notice(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : 301-399, 53-41-00Page C640 Aug 01/05
CES
R **ON A/C 151-199, 401-499,
TASK 53-41-00-220-016
Special Detailed Inspection of Fuselage Bulk Cargo Door Frames 60 and 62, between Stringer 40 and Stringer 41, RH
1. Reason for the Job
__________________
Refer to the MPD TASK: 534175-01
2. Job Set-up Information
______________________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(66)
