(2)
 Do a special detailed inspection of the inner doublers at the lower corners of the cutout for the AFT passenger/crew door, LH/RH. Do this at these locations at the forward and aft corners: - on the edge of the doublers - on the areas of the skin and doublers which agree with the shape of

 the scuff plates (Ref. NTM 534133-Part.6).

 (3)
 Write a report about the damage you find during the inspection procedure.

 (4)
 If you find damage :

 (a)
 Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.

 (b)
 If you find corrosion damage:

 -
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data

 -
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.

 (c)
 If you find other types of damage:

 -refer to the ASRM (Ref. ASRM 53-41-11-101) for the necessary data.

 EFF : ALL 53-41-00Page C617

Nov 01/04
R
 CES  5. Close-up

________ Subtask 53-41-00-370-055
 A. Repair of the Surface Protection
 (1) If necessary, repair the paint coatings in the inspection areas (Ref. TASK 51-75-12-300-003) or (Ref. TASK 51-75-12-300-001).
 Subtask 53-41-00-410-095
 B. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the insulation and the frame linings you removed for access (Ref. TASK 25-23-45-400-008) and (Ref. TASK 25-23-45-400-005).

 (3)
 Install the corner scuff plates at the AFT passenger/crew doors (Ref. TASK 53-45-15-400-001).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 EFF : ALL 53-41-00Page C618

Nov 01/04
R
 CES  TASK 53-41-00-220-009

 Special Detailed Inspection of Internal Doubler Forward and AFT of Waste Service Panel Cutout between STGR35 and STGR39 RH
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 534137-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific abrasive cloth, grade 280
 No specific access platform 1.8 m (5 ft. 11 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-12-300-001  Repair of Major Paint Damage on Light Alloy and
 Composite Material 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only) ASRM 51-11-00-001 ASRM 51-22-00-001 ASRM 53-41-11-001 NTM 534137-Part.6 ASRM 51-73-00-001 (for corrective action) ASRM 51-74-00-001 (for corrective action)
 EFF : ALL  53-41-00Page C619

Nov 01/04
R
 CES  -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

53-41-00-991-022 Fig. 659
 3. Job Set-up
__________
 Subtask 53-41-00-010-095
 A. Aircraft Maintenance Configuration
 (1) Put an access platform in position below the inspection area.
 Subtask 53-41-00-860-059
 B. Preparation of the Inspection Area
 (Ref. Fig. 659/TASK 53-41-00-991-022)

 (1) Make sure that the outer surface of the inspection area is clean and smooth.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
 WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(61)