C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
Composite Material 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only) 52-30-00-860-006 Open the Bulk Cargo-Compartment Door 52-30-00-860-008 Close the Bulk Cargo-Compartment Door 53-42-17-000-001 Removal of the BULK Cargo-Compartment Floor-Panels 53-42-17-400-001 Installation of the BULK Cargo-Compartment
Floor-Panels ASRM 51-11-00-001 ASRM 51-22-00-001 ASRM 53-41-11-101 NTM 534129-Part.6 AMM 51-74-00-001 (for corrective action) 53-41-00-991-092 Fig. 662
3. Job Set-up
__________
Subtask 53-41-00-010-167
A. Get Access
(1)
Put the ACCESS PLATFORM 2M (6 FT) in position below the bulk cargo-compartment door.
(2)
Open the bulk cargo-compartment door (Ref. TASK 52-30-00-860-006).
(3)
Remove the floor panels 161AF and 162JF (Ref. TASK 53-42-17-000-001) in the bulk cargo compartment.
Subtask 53-41-00-110-118
B. Preparation of the Inspection Areas
(Ref. Fig. 662/TASK 53-41-00-991-092)
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1)
Make sure that the surfaces of the inspection areas are clean.
(2)
If necessary, clean the surface of the inspection areas with the CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
(3)
If necessary, make the surface of the inspection areas smooth with the abrasive cloth, grade 280 .
(4)
Make sure that the inspection areas are clean and dry before you continue.
(5)
Do a visual inspection of the surfaces of the inspection areas. Look for damage, and defects in the shape of the surfaces.
(6)
If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the AMM (Ref. AMM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-refer to the ASRM (Ref. ASRM 53-41-11-101) for the necessary data.
Fuselage Bulk Cargo Door FR60 AND FR62, between STGR40 AND STGR41 Figure 662/TASK 53-41-00-991-092- 12 (SHEET 1)
R EFF : 151-199, 401-499, 53-41-00Page C644 Aug 01/05
CES
Fuselage Bulk Cargo Door FR60 AND FR62, between STGR40 AND STGR41 Figure 662/TASK 53-41-00-991-092- 22 (SHEET 2)
R EFF : 151-199, 401-499, 53-41-00Page C645 Aug 01/05
CES 4. Procedure
_________
Subtask 53-41-00-220-064
A. Special Detailed Inspection Procedure
(Ref. Fig. 662/TASK 53-41-00-991-092)
(1) Do the special detailed inspection of the fuselage bulk cargo door frames 60 and 62, between stringer 40 and stringer 41, LH (Ref. NTM 534129-Part.6).
NOTE : If the inspection areas are painted, before you do the
____
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(67)
