NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
the correct repair procedure.
5. Close-up
________
Subtask 53-41-00-942-103
A. Remove the ground support equipment.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
EFF : 301-399, 53-41-00Page B684
Nov 01/04
R
CES
Upper and Lower Corners of the AFT Emergency Skin Cutouts Figure 657/TASK 53-41-00-991-085
R EFF : 301-399, 53-41-00 Page B685 Nov 01/04
CES
(3) Remove the access platform(s).
**ON A/C ALL
TASK 53-41-00-220-003
Special Detailed Inspection of Lower Skin of Longitudinal Lap Joints in Crack Stopper Areas at Stringer 6 LH/RH between FR47 and FR70, External Surface
1. Reason for the Job
__________________
Refer to the MPD TASK: 534102-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific abrasive cloth, grade 280 No specific warning notice No specific adjustable access platform 5 m (16 ft. 5 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL 53-41-00Page B687
Nov 01/04
R
CES
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
Composite Material 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only) ASRM 51-11-00-001 ASRM 51-22-00-001 NTM 534102-Part.6 ASRM 51-73-00-001 (for corrective action) ASRM 51-74-00-001 (for corrective action) ASRM 53-41-11-101 (for corrective action) ASRM 53-41-11-201 (for corrective action) 53-41-00-991-002 Fig. 621
3. Job Set-up
__________
Subtask 53-41-00-860-050
A. Aircraft Maintenance Configuration
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
(1)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever when working near the flaps/slats.
(2)
Put the warning notice on the slat/flap control lever to tell persons not to operate the flaps.
Subtask 53-41-00-941-053
B. Get Access
(1) Put the adjustable access platform in position below the inspection area.
EFF : ALL 53-41-00Page B688
Nov 01/04
R
CES Subtask 53-41-00-860-051
C. Preparation of the Inspection Areas
(Ref. Fig. 621/TASK 53-41-00-991-002)
(1) Make sure that the surfaces of the inspection areas are clean and smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(52)
