(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
EFF : ALL 53-41-00Page A678
Nov 01/04
R
CES TASK 53-41-00-210-808
General Visual Inspection of Upper Skin of Longitudinal Lap Joints, including Crack Stopper Areas at Stringer 32 LH and Stringer 41 RH, External Surface
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 534104-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL 53-41-00Page A679
Nov 01/04
R
CES
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
ASRM 53-41-11-101 (for corrective action)
ASRM 53-41-11-201 (for corrective action)
53-41-00-991-051 Fig. 638
**ON A/C 301-399,
53-41-00-991-070 Fig. 639
**ON A/C ALL
53-41-00-991-081 Fig. 640
3. Job Set-up
__________
R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 53-41-00-010-157
A. Get Access
(1)
Put a warning notice in position to tell persons not to operate the flight controls.
(2)
Remove these access panels:
-197AB
-197BB
-197GB
-198BB
-198GBR **ON A/C 151-199, 401-499,
Subtask 53-41-00-010-157-A
A. Get Access
(1)
Put a warning notice in position to tell persons not to operate the flight controls.
(2)
Remove these access panels:
-197AB
-197BB
-197GB
-198BB
-198MB
**ON A/C 301-399,
Subtask 53-41-00-010-157-B
A. Get Access
(1)
Put a warning notice in position to tell persons not to operate the flight controls.
(2)
Remove these access panels:
-197AB
-197GB
-197KB
-198GB
-198KB
**ON A/C ALL
Subtask 53-41-00-110-091
B. Cleaning Procedure
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Clean the area with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-004), and let the area dry.
4. Procedure
_________
(Ref. Fig. 638/TASK 53-41-00-991-051)
**ON A/C 301-399,
(Ref. Fig. 639/TASK 53-41-00-991-070)
**ON A/C ALL
(Ref. Fig. 640/TASK 53-41-00-991-081)
R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 53-41-00-210-110
A. Inspection
(1) Examine the following areas for scratches, dents and cracks:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(30)
