-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
 4. Procedure
_________
 (Ref. Fig. 401/TASK 53-55-13-991-001)
 Subtask 53-55-13-914-050
 A. Preparation for Installation:
 (1) Clean the mating surfaces of the fairing with a nonmetallic scraper, CLEANING AGENTS (Material No. 11-003) and a lint-free cloth.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
 SPECIAL MATERIAL.
 THIS MATERIAL IS DANGEROUS.

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (2)
 Clean the component interface and/or the adjacent area.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Apply SEALANTS (Material No. 09-018) to the fairing interface and the screws (1).

 EFF : ALL
53-55-13Page 407

 Subtask 53-55-13-420-050
 B. Installation:
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Put the fairing (2) in position. CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE

_______ MADE OF CARBONFIBER REINFORCED PLASTIC.

 (3)
 Install the screws (1).

 5. Close-up
________ Subtask 53-55-13-410-050
 A. Close Access
 (1)
 Install the lower trimmable horizontal-stabilizer aprons (Ref. TASK 55-15-11-400-001).

 (2)
 Remove the access platform(s).

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 Subtask 53-55-13-865-052
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CC1, 5CC2, 14CC1, 14CC2, 15CC, 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 21CE1, 21CE2, 21CE3, 22CE.
 EFF : ALL
53-55-13Page 408

 FITTINGS - DESCRIPTION AND OPERATION
____________________________________
 1. General_______
 Fittings make it possible to attach components to the structure, and to attach the tailcone to the cone/rear fuselage.
 2. Component Location__________________ (Ref. Fig. 001)
 3. Description___________
 A. The Cone/Rear Fuselage Fittings The fittings which are installed on the cone/rear fuselage are made of forged aluminum alloy.
 B. The Vertical Stabilizer Fittings The fittings for the vertical stabilizer are part of the FR70, FR72 and FR74.
 C. The Horizontal Stabilizer Fittings The fittings for the horizontal stabilizer are installed on FR77 and are removable.
 D. The Tailcone Atachment Fittings The fittings for the attachment of the tailcone are part of the FR77.
 EFF : ALL
53-56-00Page 1

 Fittings
 Figure 001
 EFF :  ALL  53-56-00 Page 2 
Feb 01/98
 CES 

 FITTINGS - TRIMMABLE HORIZONTAL STABILIZER - REMOVAL/INSTALLATION
_________________________________________________________________
 TASK 53-56-11-000-001
 Removal of the Support Fittings of the Trimmable Horizontal Stabilizer (THS)
 NOTE : The removal procedures are given for the left Support Fittings; the
____ removal procedures for the right Support Fittings are almost the same.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.) No specific adjustable access platform 5.0 m (16 ft. 5 in.) SL90-314-4375 1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-374-4375 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 98D27407505000 1 EXTRACTOR - CENTERING BUSH, THS 98D27408406000 1 DISTANCE STRUT - FRAME 77
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(130)