5. Close-up
________ Subtask 53-51-00-916-057
A. Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to the inspection area (Ref. TASK 51-75-13-916-001).
Subtask 53-51-00-410-067
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the rear pressure-bulkhead cover (1).
(3)
Close the access door 312AR.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-51-00Page 652
Rear Pressure Bulkhead, Aft Face Skin Splices
Figure 613/TASK 53-51-00-991-014
EFF : ALL 53-51-00 Page 653
Feb 01/98
CES
TASK 53-51-00-210-016
Detailed Visual Inspection of Rear Pressure Bulkhead, Areas around Outlet Cutouts, AFT Face
1. Reason for the Job
__________________
Refer to the MPD TASK: 535111-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific lint-free cloth
No specific access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 15-005 AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-006 AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-13-916-001 Repair to a layer of Moisture-Removing Oil ASRM 535100000 (for corrective action) 53-51-00-991-015 Fig. 614
EFF : ALL
53-51-00Page 654
3. Job Set-up__________
Subtask 53-51-00-010-070
A. Get Access
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION_______
R BEFORE YOU START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL_______
R MATERIAL.
R THIS MATERIAL IS DANGEROUS.
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Put the access platform in position below the access door 312AR.
R
(2) Open the access door 312AR.
(3) Remove the rear pressure-bulkhead cover (1).
(4) Carefully clean the inspection area with CLEANING AGENTS (Material
No. 11-004) and a lint-free cloth.
R
EFF : ALL
53-51-00Page 655
Feb 01/99
4. Procedure
_________
(Ref. Fig. 614/TASK 53-51-00-991-015) Subtask 53-51-00-210-068
A. Inspection:
(1) Examine the cutouts of the aft face of the rear pressure bulkhead for:
-cracks.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 535100000) for the
____
correct repair procedure.
5. Close-up
________
(Ref. Fig. 614/TASK 53-51-00-991-015) Subtask 53-51-00-916-058
A. Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to the inspection area (Ref. TASK 51-75-13-916-001).
Subtask 53-51-00-410-068
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(111)
