(2)
Make sure that the warning notice is in position to tell persons not to move the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______ BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
Subtask 53-53-11-864-051
B. Make sure that the Green, Yellow and Blue hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).
EFF : ALL
53-53-11Page 415
Subtask 53-53-11-865-054
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/FCDC1/SPLY 20CE1 B10 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU FLIGHT CONTROLS/FCDC2/SPLY 20CE2 Q20 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
4. Procedure_________
(Ref. Fig. 402/TASK 53-53-11-991-002)
Subtask 53-53-11-916-050
A. Preparation for Installation:
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Apply COMMON GREASE (Material No. 04-004) to the bolts (1).
Subtask 53-53-11-420-053
B. Installation:
(1)
Put the support strut (5) in position and install the bolts (1).
(2)
Install the washers (2) and the nuts (3).
NOTE : Do not tighten the nuts at this time.
____
EFF : ALL
53-53-11Page 416
May 01/03
R
CES
(3)
Make sure that the clearance 'x' is 14.5 +2.5 -2.5 mm (0.5708 +0.0984 -0.0984 in.) between the THS attach support and the outer attach fittings.
(4)
If necessary align the THS:
(a)
Remove and discard the lockwire.
(b)
Loosen the locknuts (11).
(c)
Remove the two support struts at the side where the clearance is lowest.
(d)
Adjust the other two support struts until the clearance 'x' is correct.
(e)
Install the support struts.
(f)
TORQUE the locknuts (11) to between 11.00 and 13.00 m.daN (81.12 and 95.87 lbf.ft)
(g)
Safety the nuts (11) with corrosion-resistant steel lockwire 0.8 mm (0.032 in) dia..
(5)
TORQUE the nuts (3) to between 2.60 and 3.00 m.daN (19.17 and 22.12 lbf.ft).
(6)
Safety the nuts (3) with the new cotter pins (4).
(7)
Install the bonding straps (8) and (10) with the screws (6), the washers (7) and the nuts (9) (Ref. TASK 20-28-00-912-004).
(8)
Apply STORAGE PRESERVATION (Material No. 15-007) to the area (Ref. TASK 51-75-13-916-002).
5. Close-up
________
(Ref. Fig. 402/TASK 53-53-11-991-002) Subtask 53-53-11-865-055
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 20CE1, 20CE2, 21CE1, 21CE2, 21CE3, 22CE.
EFF : ALL
53-53-11Page 417
Subtask 53-53-11-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the THS fairings (Ref. TASK 53-55-13-400-001).
(3)
Install the THS aprons (Ref. TASK 55-15-11-400-001).
(4)
Close the access doors 312AR and 314AR.
(5)
Remove the warning notice(s).
(6)
Remove the access platform(s).
(7)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(123)
