R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-013A C Z-24.223
RELEASE AGENT (Ref. 20-31-00)
Material No. 09-016A USA MIL-PRF-81733D
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3
CORROSION INHIBITING LOW ADHESION SEALANT
(Ref. 20-31-00)
Material No. 11-003 USA ASTM D 740
METHYL-ETHYL-KETONE (Ref. 20-31-00)
EFF : ALL
53-55-11Page 405
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 53-55-11-991-001 Fig. 401
3. Job Set-up
__________
Subtask 53-55-11-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft is in the same configuration as for the removal task.
(2)
Make sure the warning notices are in position to tell persons not to operate the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
Subtask 53-55-11-864-051
B. Make sure that the Green, Yellow and Blue hydraulic systems are depressurized. (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003)
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES
_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
EFF : ALL
53-55-11Page 406
Subtask 53-55-11-865-051
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R R R R 49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 49VU AUTO FLT/FAC1/28VDC 49VU AUTO FLT/FAC1/26VAC 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 105VU FLT CTL/ELAC1/STBY SPLY 105VU FLT CTL/SEC1/STBY SPLY 121VU AUTO FLT/RUDDER/TRIM/IND 121VU AUTO FLT/FAC2/28VDC 121VU AUTO FLT/FAC2/26VAC 121VU FLIGHT CONTROLS/SEC3/SPLY 121VU FLIGHT CONTROLS/SEC2/SPLY 121VU FLIGHT CONTROLS/THS ACTR/MOT3 121VU FLIGHT CONTROLS/THS ACTR/MOT1 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE1 19CE2 21CE1 5CC1 14CC1 16CE2 16CE1 22CE 15CC 5CC2 14CC2 21CE3 21CE2 19CE3 19CE1 15CE2 B11B09B08B04B03 A02 A01 B01 M20M19M18Q19Q18Q17Q16R20
4. Procedure_________
(Ref. Fig. 401/TASK 53-55-11-991-001)
Subtask 53-55-11-914-050
A. Preparation for Installation:
(1) Clean the mating surfaces of the fairing with a nonmetallic scraper, CLEANING AGENTS (Material No. 11-003) and a lintfree cloth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE_______ SPECIAL MATERIAL. THIS MATERIAL IS DANGEROUS.
EFF : ALL
53-55-11Page 407
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(125)
