ASRM 53-46-11-001 (for corrective action) 53-41-00-991-026 Fig. 623
3. Job Set-up
__________
Subtask 53-41-00-010-104
A. Get Access
(1)
Remove the door frame linings (Ref. TASK 25-23-45-000-003), (Ref. TASK 25-23-45-000-004).
(2)
Remove the thermal and acoustical insulation blankets (Ref. TASK 25-80-00-000-001).
NOTE : Identify the blankets for installation.
____
(3) Cleaning.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a) Clean the door stop fittings with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
EFF : ALL
53-41-00Page 694
Feb 01/02
R
CES 4. Procedure
_________
(Ref. Fig. 623/TASK 53-41-00-991-026) Subtask 53-41-00-210-087
A. Inspection
(1) Examine the door stop fittings for:
-wear,
-cracks.
NOTE : If necessary refer to the ASRM (Ref. ASRM 53-46-11-001) for
____ the limits and the correct repair procedure.
5. Close-up
________ Subtask 53-41-00-410-103
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the thermal and acoustical insulation blankets (Ref. TASK 25-80-00-400-001).
(3)
Install the door frame linings (Ref. TASK 25-23-45-400-008), (Ref. TASK 25-23-45-400-005).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-41-00Page 695
Feb 01/02
R
CES
Door Stop Fittings Figure 623/TASK 53-41-00-991-026
R EFF : CES ALL 53-41-00 Page 696 Feb 01/02
TASK 53-41-00-210-030
Detailed Visual Inspection of Fuselage Internal Structure, Below Cabin Floor Panels Including Floor Structure from FR65 to FR70
1. Reason for the Job
__________________
Refer to the MPD TASK: 534144-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.8 m (5 ft. 11 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
Material No. 15-005 AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-006 AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL
53-41-00Page 697
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-55-12-000-001 Removal of the AFT Cargo Compartment Partition FR65 25-55-12-400-001 Installation of the AFT Cargo Compartment Partition
FR65 25-80-00-000-001 Removal of the Insulation Blankets 25-80-00-400-001 Installation of the Insulation Blankets 51-75-13-916-002 Repair to a layer of Corrosion Preventive Compound 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-003 Open the FWD or AFT Cargo-Compartment Door with the Hand Pump 52-30-00-860-004 Close the FWD or AFT Cargo-Compartment Door with the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(11)
