(2)  
If you adjust the door when the airplane is on jacks, you must complete the adjustment with the airplane on its wheels.

 (3)  
The adjustment of the stop pins, the door flushness, and the handle torque must be checked when the airplane is on its wheels.

 (4)  
There are 15 necessary conditions that the door must have to be rigged correctly (Figure 501A).

 (5)  
Successful completion of the checks in table 501 shows that the door is rigged correctly.

 B.
Special Tools and Equipment

 (1)  
Maintanance stand

 (2)  
Bearing retainer nut spanner wrench - F70085

 (3)  
Spring Scale - 0 to 50 pound capacity

 (4)  
90-pound weight

 (5)  
A 60-pound weight.

 C.
Standard Tools and Equipment

 (1)  
Modeling Clay

 (2)  
Petroleum Jelly

 (3)  
Rig Pin

 (4)  
C52006-1 Rigging Simulator - Escape Slide

 D.
References

 (1)  
25-61-35/201, Emergency Escape Assembly (Door-Mounted)

 (2)  
52-41-31/401, Galley Service Door Lining and Insulation

 E.
Access

 (1)  
Location Zone
 106 Forward Galley Service Door
 112 Aft Galley Service Door

 F.
Procedure

 S 845-048-B00
 (1)  
Prepare to adjust the door.

 (a)  
Put a maintenance stand adjacent to the door.

 (b)  
Remove the escape slide from the door (25-61-35/201).

 (c)  
Remove the door lining (Ref 52-41-31/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-41-00
 ALL  ú ú B01A Page 503 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  Attach a 90-pound weight approximately in the middle of the bottom half of the FWD door. Attach a 60-pound weight approximately in the middle of the bottom half of the AFT door.
 NOTE: This weight makes the door operate as if the escape
____
 slide was installed.

 1) You may use the rigging simulator tool, C52006-1.
 (e)  ON A NEW DOOR; do these steps: 1) Remove the centering guide from the door. 2) Back off all the door stop pins so they will not interfere
 with the adjustment. 3) Loosen all the latch fittings until they move easily over their serrated plates.
 S 825-029-B00
 (2)  
Adjust the door:

 (a)  
ON A NEW DOOR; do each adjustment in Figure 501A to get each necessary condition.

 (b)  
Do the checks in Figure 501A to identify problem areas.

 (c)  
Do the adjustments in Figure 501A to correct problems.

 (d)  
Use Figure 501A until you have all the necessary conditions at the same time.

 NOTE:____Adjustments are related. When you change one of them, you must continue to check and change the other adjustments until they are all satisfactory.
 S 825-052-B00
 (3)  
Adjust the snubber on the bottom hinge.

 (a)  
Open the door.

 (b)  
Make the snubber longer if it keeps the door from the fully open position. 1) Remove the four bolts that hold the fitting to the

 structure. 2) Turn the rod end to change the length of the snubber. 3) Attach the fitting to the structure with the four bolts.
 S 435-021-B00
 (4)  
Install the centering guide if you removed it.

 (5)  
Adjust the centering guide as shown in figure 517.

 S 825-053-B00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-41-00
 ALL  ú ú B01A Page 504 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 825-023-B00
 (6)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 艙門 DOORS 1(125)