52-21-00
ALL ú ú B03 Page 404 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
EMERGENCY EXIT HATCH - ADJUSTMENT/TEST
______________________________________
1. General
_______
A. This procedure contains two tasks:
(1)
The adjustment of an emergency exit hatch
(2)
The system test of an emergency exit hatch.
TASK 52-21-00-805-001-B00
2. Adjust the Emergency Exit Hatch (Fig. 501)
_______________________________
A. General
(1)
This procedure refers to the emergency exit hatch as "the hatch".
B.
Special Tools and Equipment
(1)
A push-pull gage that can measure 0 to 50 lbs.
(2)
Shims made of laminations - BACS40B24-34
(3)
Washers - AN960-10L
(4)
Shims - 69-36674-5
(5)
Shims - 63-2541-1
(6)
Shims - 69-36674-7
C.
References
(1)
52-21-00/001, Emergency Exit Hatch
(2)
52-21-12/401, Emergency Exit Hatch Lining
D.
Access
(1)
Location Zone
116 Right Emergency Exit Hatch
117 Left Emergency Exit Hatch
(2)
Access Panel
2403L Left Emergency Hatch
2404R Right Emergency Hatch
E.
Procedure
(1)
Remove the lining from the hatch (Ref 52-21-12/401).
S 825-005-B00
(2)
Adjust the hatch vertically.
(a)
Change the thickness of the shims below the lower pivot fitting to move the hatch vertically.
(b)
Adjust the hatch until the stop pins have less than the 0.06 inch dimension shown (Detail B).
S 035-025-B00
NOTE: This dimension is between the axis of the
____ stop pin and the axis of the stop fitting.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-21-00
ALL ú ú B02 Page 501 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ROLLER ASSEMBLY
HATCH SEE F (2 LOCATIONS)
SEE A LATCH ASSEMBLY
SEE C STOP FITTING (6 LOCATIONS)
SEE B PIVOT FITTINGFRAME HATCH STOP FITTING (2 LOCATIONS)
4. STOP PIN
LOCKSPRING
SEE D OF THE STOP PIN ON THE HEEL PAD
5. FRAME STOP
HATCH
SEE EFITTING
HATCH
OF THE STOP A PIN ON THE
6. SEAL
FRAME
0.06 INCH MAXIMUM NOT ALIGNED
HATCH
STOP FITTING
B
1. FRAME
BELLCRANK
HANDLE FRAME
ASSEMBLY
RELEASE
HANDLE
2.
LATCH PLATE (WITH SERRATIONS)
3.
LATCH FITTING
TORQUE TUBE
LATCH ASSEMBLY
C1
TORSION SPRING
1THIS VIEW DOES NOT SHOW THE COVER
Adjustment of the Emergency Exit Hatch Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-21-00
ALL ú ú B02 Page 502 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
7. PIVOT
9. PLATE (WITH SERRATIONS)
FITTING
PIVOT HOOK
8. SHIMS (MADE OF LAMINATIONS)
A (BACS40B-24-34)
A
HATCH
PIVOT FITTING
D
6. PRESSURE SEAL
10.
HEEL PAD (2 LOCATIONS)
11.
WASHERS (AN960-10L)
HEEL PADS
E
TOP SILL
SHIM (MADE OF LAMINATIONS)
ROLLER GUIDE BLOCK
ROLLER ASSEMBLY TOP OF THEHATCH
ROLLER ASSEMBLY PIVOT FITTING
F
0.06
INCH
0.02
PIVOT HOOK
SILL
A-A
Adjustment of the Emergency Exit Hatch Figure 501 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 艙門 DOORS 1(91)
