Forward Entry Door Adjustment
Figure 501 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-00
 ALL  ú ú B01 Page 506 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
20. PLATE
CHANNEL
21.
 ADJUSTABLE GUIDE

22.
 BOLT

 3. GUIDE TRACK
THESE PARTS ARE ON THE DOOR23. GUIDE PIN
GUIDE TRACK
F
CONTROL ROD  33. DOOR
 COCKING  34. PUSH ROD 
LATCHING  CRANK 
CRANK 

MECHANISM HOUSING
29. NUT
CAM PLATE
30.
 BEARING

31.
 TORQUE TUBE CONTROL ROD

30. BEARING CAM ROLLER
29. NUT
35. ROD END BEARING
32. TORQUE TUBE
 CRANK INSIDE HANDLE
PINRECESS (IN EXTERNAL 24. OUTSIDE HANDLE
SKIN OF THE DOOR) HANDLE SHAFT
25.
 RETAINING WASHER

26.
 SPRING RETAINING NUT

27.
 SPRING

28.
 LOCK RING

HANDLE MECHANISM 
____NOTE:  CLOSED AND LATCHED. MECHANISM SHOWN  G 
Forward Entry Door Adjustment Figure 501 (Sheet 4) 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-00
 ALL  ú ú B05 Page 507 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (2)  
Access Panel
 4201L Forward Entry Door

 F.  
Prepare to adjust the door.

 S 015-008-B00
 (1)  
Remove the escape slide from the door (25-61-35/201).

 S 015-009-B00

 (2)  
Remove the door lining and the insulation (Ref 52-11-31/401).

 S 015-010-B00

 (3)  
Remove the access panel (4) from the door structure.

 S 485-012-B00

 (4)  
Attach a 90-pound weight approximately in the middle of the bottom half of the door.

 NOTE:  This weight is equivalent to the escape slide and the door liner .
 (a)  
You may use the rigging simulator tool, C52006-1.

 G.  
Adjust the Forward Entry Door Guide Arm

 S 825-013-B00
 (1)  
Open the door and move it until it is parallel to the contour of the fuselage near the closed position.

 S 825-014-B00

 (2)  
To make sure the door is parallel, do a check for these two
 conditions:

 (a)  
The forward edge of the door next to the latch receiver must be

 0.50 +/-.10 inch (12.7 +/-2.54mm) inboard of the fuselage skin.
 (b)  
While maintaining the position and dimension on the forward edge of the door, the distance between the aft edge of the door next to the aft latch receiver must be within +/-.20 inch (5.08mm) of the forward edge dimension.

 (c)  
If the door is not parallel to the contour of the fuselage after taking the above dimensions, adjust the guide arm.

 NOTE:  Make the guide arm shorter to move the aft edge of
____ the door inboard. Make the guide arm longer to move the aft edge of the door outboard.
 1)  Move the door until the forward and the aft latch rollers engage the latch fittings at the same time.
 (d)  Make sure the lubrication fitting on the guide arm is inboard.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-00
 ALL  ú ú B02 Page 508 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

INCH

INCH

-0.20
0.06
INCH-0.30
DOOR FLUSHNESS  DOOR CLEARANCE
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 艙門 DOORS 1(38)