曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
A
737-300/400/500MAINTENANCE MANUAL
 3)  Procedure C. This procedure replaces the damaged part of the seal with a piece of replacement seal. Do one of these steps: a) Miter the seal to get the correct fit, and use
 Procedure A to bond the seal with adhesive only.
 b)  Miter the seal to get the correct fit, and use Procedure B to bond the seal with adhesive and Dacron fabric.
Consumable Materials
 (1)  
A00336 Adhesive - General Electric SR-529 Adhesive Base with SRC-18 Catalyst

 (2)  
A00923 Adhesive - BAC 5010 Type 77, Silicon Resin GE PSA-529 with SRC-18 Catalyst

 (3)  
A00341 Adhesive - RTV 732 Clear

 (4)  
A00553 Adhesive - BAC 5010 Type 68

 (5)  
A00027 Adhesive - Dow Corning Q3-7063

 (6)  
A00294 Adhesive - General Electricl RTV 108

 (7)  
A00072 Adhesive - Dow Corning DC 93-076 1/8 with catalyst

 (8)  
G00028 Fabric - Dacron Tricot Reinforcing D117 or D118

 (9)  
B00148 Solvent - Methyl Ethyl Ketone (MEK), TT-M-261

 (10)
 B00137 Abrasive paper

 (11)
 G00033 Cheesecloth, BMS 15-5Access

 (1)  
Location Zones 105 Forward Entry Door 106 Forward Galley Service Door 110 Aft Entry Door 112 Aft Galley Service Door 116 Right Emergency Exit Hatch 117 Left Emergency Exit Hatch 209 Forward Cargo Door 219 Aft Cargo Door

Prepare to repair the seal.
 S 348-002-B00
 (1)  
Make a decision about the correct adhesive.

 (a)  
Use Type I adhesive for the parts of the seal that are not flexible.

 NOTE: Do not use Type I adhesive on the diaphragm seals or
____
 on the lip of the blade seals.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-09-10
 ALL  ú ú B02 Page 804 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Use Type II adhesive where it is necessary for the seal to be very flexible.

 (c)  
Use Type III adhesive for fast repairs.

 NOTE:____Type III is very flexible. You can use it on any part of any seal.
 S 348-003-B00
 (2)  Prepare the adhesive.
 NOTE:____Type II adhesive has only one part. It is not necessary to prepare Type II adhesive before you use it.
 (a)  Mix the parts of the Type I adhesive. 1) Put together only the amount of adhesive that is necessary. 2) Weigh the parts to get the correct ratio. 3) Use 100 parts of General Electric SR-529 adhesive to 4.5
 parts of SCR-18 catalyst.
 NOTE: The pot life is 8 hours at 70°F.
____
 (b)  Mix the parts of the Type III adhesive. 1) Do these steps to mix the Dow Corning adhesive: a) Put together only the amount of adhesive that is
 necessary. b) Weigh the parts to get the correct ratio. c) Use 100 parts of Dow Corning 93-076-1/8 adhesive to 10
 parts of catalyst.
 NOTE: The pot life is 2 hours.
____
 2)  Do these steps to mix the RTV 700 adhesive: a) Select the correct catalyst.
 NOTE: Beta 2 will only let the adhesive flow for
____ approximately 45 minutes after you mix it. Use it when you do not want the adhesive to flow. Beta 1 or Beta 4 will let the adhesive flow for the entire 3 hour pot life of the adhesive. Use them when it is satisfactory to let the adhesive flow.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-09-10
 ALL  ú ú B01 Page 805 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 b) Mix the catalyst and the adhesive.
 E.  Repair the Seals
 S 118-004-B00
 (1)  Prepare the surfaces of the repair.
 WARNING: DO NOT GET METHYL ETHYL KETONE (MEK) IN YOUR MOUTH OR
_______ EYES, OR ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM MEK. PUT ON SPLASH GOGGLES AND GLOVES WHEN YOU USE MEK. KEEP MEK AWAY FROM SPARKS, FLAME, AND HEAT. MEK IS A POISONOUS AND FLAMMABLE SOLVENT WHICH CAN CAUSE INJURY OR DAMAGE.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 艙門 DOORS 1(13)