(g)
Move the door aft until the latch plate on the top carriage goes over the stop latch on the top track.
(h)
Move the door forward until the latch plate is against the stop latch on the track.
(i)
Adjust the aft top and the bottom snubbers to get 0.10 inch between the carriage and the face of the snubber.
S 864-017
(8)
Close and latch the door.
S 824-018
(9)
Do a check of the handle torque as follows:
(a)
Turn the handle to the open position.
(b)
Measure the torque that is necessary to move the handle during the first 10 degrees of handle motion.
(c)
See that the torque is from 144 pound-inches to 240
pound-inches.
(d)
If the torque is not satisfactory, adjust the latch fittings as follows: 1) Loosen the fasteners in the latch cam fitting. 2) Move the fitting inboard if it is necessary to make the
handle torque less. 3) Move the fitting outboard if it is necessary to make the handle torque more. 4) Tighten the fasteners in the latch fitting and do a check of the handle torque again.
S 824-019
(10)
Make sure the door flushness and clearance is correct (Fig. 402).
S 424-020
(11)
Install the door lining, cover, and reveals.
S 824-021
(12)
Adjust the seal around the outside of the door lining to get 0.05 |0.05 inch clearance when the seal enters the reveal (Fig. 403).
(13)
Close and latch the door.
S 824-023
(14)
Do a check of the handle torque as follows:
(a)
Turn the handle to the open position.
(b)
Measure the torque that is necessary to move the handle during the first 10 degrees of handle motion.
(c)
See that the torque is not more than 300 pound-inches.
S 864-022
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-13-01
ALL ú ú 02 Page 414 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 434-024
(15) Make sure the seal is as shown in Figure 403.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-13-01
ALL ú ú 02 Page 415 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
RECESSED
DOOR HANDLE EXTERIOR
HOUSING DOOR HANDLE
RECESSED
FAIRING
HOUSING
EXTERIOR FIXED
DOOR HANDLE FAIRING
SEE C
SEE B
(T-SHAPED HANDLE
(BUTTERFLY HANDLE WITH FIXED FAIRING
RECESSED FLUSH WITH RECESSED INTO HOUSING)
BODY SKIN INTO HANDLE
HOUSING WHEN STOWED)
EXTERNAL DOOR HANDLE EXTERNAL DOOR HANDLE
(CONFIGURATION 1) (CONFIGURATION 2)
A A
EXTERNAL
DOOR
HANDLE
SEE A
HANDLE
HOUSING
CL
DOORCL
HANDLE
1. SCREW (8-10 DEG
OFFSET)
2. COVER
PANEL
CONFIGURATION 2
INTERNAL DOOR HANDLE
Internal and External Door Handles Figure 401 (Sheet 1)
H72583
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ONLY ú
52-13-03
ú ú 01 Page 401 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
6. COTTER PIN 3. COTTER PIN
4. WASHER
7. WASHER
10. CAM ASSEMBLY
5. PIN
11. NUT 8. PIN
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(131)
