A-A
SEAL RETAINER
SCREW SEAL SUPPORT RAIN SEAL
NUTPLATE ANGLE
FUSELAGE STRUCTURE
DOOR SEAL RETAINER SCREW RAIN NUTPLATE SEAL
SEAL TOP ATTACHMENT SEAL DOOR ATTACHMENT
A B
Rain Seal
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-03
ALL ú ú 01 Page 402 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 024-006
(6) Pull the seal from the fuselage structure. Be careful when you pull the seal to not cause damage to the seal.
TASK 52-09-03-404-007
3. Install the Rain Seal (Fig. 401)_____________________
A. Standard Tools and Equipment
(1)
Spatula or Flow Gun
B.
Consumable Materials
(1)
A00140 Compound - Sealing, BMS 5-19, Class B
(2)
B00148 Solvent - Methyl Ethyl Ketone (MEK), TT-M-261
(3)
G00000 Agent - Parting, Delchem X-769
(4)
G00033 Cheescloth - Woven, BMS 15-5, Class A
C.
References
(1)
IPC 52-09-03 Fig. 1
D.
Access
(1)
Location Zones
821R Forward Cargo Door
822R Aft Cargo Door
E.
Prepare to Install the Rain Seal
S 114-017
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
(1)
Remove the unwanted sealant from the door surface and the fuselage structure. Use IPA, or Ethyl Alcohol if it is necessary.
S 114-010
(2)
Clean the mating surfaces with a clean cheesecloth and IPA, or Ethyl Alcohol .
S 114-011
(3)
Clean with the IPA, or Ethyl Alcohol and a clean cloth until there are no soils.
S 884-012
(4)
Let the surfaces dry.
F.
Install the Rain Seal
(1)
Put the rain seal in the correct position (View A-A, Fig. 401).
S 424-013
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-03
ALL ú ú 01 Page 403 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(2) S 344-014Apply the parting agent to the seal's mating surfaces on the fuselage structure and the door. (Views A and B, Fig. 401).
(3) S 864-019Let the surfaces dry.
(4) S 344-015Use a spatula or flow gun to apply the sealant to the mating surface of the rain seal to get a layer approximately 1/32 inch thick.
(5) S 434-016Install the rain seal to the door and the fuselage structure with the screws (Views A and B, Fig. 401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-03
ALL ú ú 01 Page 404 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
DIAPHRAGM-MECHANICAL SEALS - REMOVAL/INSTALLATION
_________________________________________________
1. General_______
A. This procedure contains two tasks. The first task is the removal of the diaphragm-mechanical seal. The second task is the installation of the diaphragm-mechanical seal.
B. Diaphragm seals can be disconnected from the door without the removal of the full diaphragm-mechanical seal. For the diaphragm seal removal/installation, refer to 52-09-01/401, Diaphragm Seals.
TASK 52-09-04-004-001
2. Remove the Diaphragm-Mechanical Seal (Fig. 401)____________________________________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(15)
