S 424-039
 (2)  
Install the upper bearing plate (53) on the lower hinge housing (36) and install the bolt.

 S 394-016

 (3)  
Apply the sealant around the upper bearing plate (53) (Ref
 51-31-01/201).

 S 424-017

 (4)  
Install the lower hinge arm.

 (a)  
Attach the lower shaft (25) to the hinge arm (33) with the bolt (24).

 NOTE: Two spaces, one between the teeth on the hinge arm, and
____ the other between the teeth on the shaft, are used to align the hinge arm in the shaft.
 (b)  
Attach the lower shaft (25) to the lower coupling with the bolt.

 (c)  
Fill the hole above the upper bearing (35, between the shaft and the bearing housing) at the lower hinge arm (33) with grease to prevent water go into the bearing.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 411 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (5)  S 094-018Remove the sling.
 (6)  S 414-019Close and latch the door.
 (7)  S 214-040Make sure the door flushness tolerances are satisfactory (Ref 52-11-01/501 for Doors 1, or 52-11-09/501 for Door 5).
 (8)  S 824-021Adjust the latch fittings on the serrated plates to align the door, if it is necessary.
 (9)  S 224-022Do an alignment check of the flange holes in the upper and lower couplings (Detail A, Fig. 401).
 S 434-023

 (10)
 Install the elbow pins (45) and washers (44) in the upper coupling.

 S 434-024

 (11)
 Attach the lower coupling to the upper coupling with the bolt, if the holes in the upper and lower couplings aligned.

 S 434-025

 (12)
 Install the new lower coupling, if the holes in the upper and lower couplings do not align.

 (a)  
Install the new lower coupling on the lower shaft (25).

 (b)  
Use the upper coupling as a template to make a mark of the hole locations on the new lower coupling.

 (c)  
Remove the new lower coupling from the lower shaft (25) and drill the holes, if it is necessary.

 (d)  
Install the new lower coupling on the lower shaft (25).

 (e)  
Install the elbow pins (45) and washers (44) in the upper coupling and the new lower coupling.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 412 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 824-041
 (13)
 If you adjusted the latch fitting in step 3. G. (8), do a check of the other rigging adjustments that related (Ref 52-11-01/501 Doors 1 or 52-11-09/501 Door 5).

 S 414-027

 (14)
 Install the access panel (6) on the door torque tube, if you removed.

 S 414-028

 (15)
 Install the access panels (9, 3) on the upper and lower hinges.

 S 394-029

 (16)
 Apply the sealant around the edge of the hinge access panels (9, 3), if it is necessary (Ref 51-31-01/201).

 S 414-030

 (17)
 Install the hinge covers (11, 29).

 S 424-042

 (18)
 Install the shim to keep the flushness tolerances on the hinge cover (Ref 52-11-01/501 for Door 1, or 52-11-09/501 for Door 5).

 S 224-032

 (19)
 Make sure the hinge cover clearances are correct as shown in Fig. 402.

 (20)
 Cut the edges of the covers (11, 29), if it is necessary.

 (21)
 Install the door lining (Ref 52-11-02/401).

 S 824-033
 S 414-035
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 413 ú Oct 18/99
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(51)