28.
 BOLT (4 LOCATIONS)

29.
 HINGE COVER

30. SPACER (4 LOCATIONS)
57. BOLT
60. WASHER
58.
 WASHER

59.
 NUT

31. WASHER ( 2 LOCATIONS)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 403 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

16. UPPER HINGE HOUSING
17. BOLT 
(3 LOCATIONS)  54. BOLT 
57. WASHER 
20. LOWER  55. WASHER 
BEARING  18. BEARING  56. NUT 
PLATE  19. SEAL  45. TAPPERED PIN 
21. WASHER  23. BOLT  (4 LOCATIONS) 
22. NUT  44. WASHER 
51. WASHER (2 LOCATIONS)  50. UPPER SHAFT  (8 LOCATIONS) 

52. NUT 43. BOLT
40. WASHER
42. NUT (4 LOCATIONS)41. NUT
48.
 BOLT

49.
 CRANK

47. WASHER
46. NUT
25. LOWER SHAFT
37. BOLT (3 LOCATIONS) 24. BOLT
26. WASHER 53. UPPER BEARING PLATE
27. NUT
34. SEAL 14. WASHER 38. WASHER 35. BEARING (2 LOCATIONS)
39. NUT
29. HINGE  15. NUT CAP COVER (2 LOCATIONS)
36. LOWER HINGE 33. LOWER
HOUSING HINGE ARM
54. BOLT
59. WASHER
12. WASHER (4 LOCATIONS)
55. WASHER
10. BOLT
B  (2 LOCATIONS) 56. NUT
Main Entry Door Hinge Arms Figure 401 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 404 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Make sure the seal is applied around the edge of the access panel (9) on the upper hinge for installation.

 (c)  
Remove the elbow pins (45) from the upper and lower couplings.

 (d)  
Disconnect the control rod from the crank (49).

 (e)  
Remove the bolt (23) that attaches the upper shaft (50) to the upper hinge arm (13) and move the upper shaft clear of the hinge arm.

 (f)  
Remove the bolts (17) that attaches the lower bearing plate (20) to the upper hinge housing (16) and remove the bearing plate.

 (g)  
Remove the upper hinge arm (13) from the upper hinge housing (16).

 F.
Remove the Lower Hinge Arm

 S 014-008
 (1)  
Open the main entry door.

 S 494-009

 (2)  
Attach the sling and apply sufficient tension to release the hinges of the door weight.

 S 024-010

 (3)  
Remove the lower hinge arm.

 (a)  
Remove the access panels (3 and 6) on the lower hinge, the torque tube (if installed) and the hinge cover (29, Detail A).

 (b)  
Make sure the seal applies around the edge of the access panel (3) on the lower hinge for installation.

 (c)  
Remove the elbow pins (45) from the upper and lower couplings.

 (d)  
Remove the bolts (43, 24) that attach the upper and lower ends of the lower shaft (25) to the lower coupling and the lower hinge arm (33).

 (e)  
Remove the bolts that attach the upper bearing plate (53) to the lower hinge housing (36).

 (f)  
Move the lower shaft (25) clear of the lower hinge arm (33).

 (g)  
Remove the upper bearing plate (53) and the hinge arm from the hinge housing (36).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-03
 ALL  ú ú 03 Page 405 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 TASK 52-11-03-404-011
 3. Hinge Arm Installation (Fig. 401)
______________________
 A. Special Tools and Equipment
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(48)