曝光臺 注意防騙
網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者
SUBTASK 27-41-94-860-003
(2) Remove the safety tag and close this circuit breaker:
F/O Electrical System Panel, P6-2
Row Col Number Name
B 10 C00207 FLIGHT CONTROL STAB TRIM CONT
SUBTASK 27-41-94-820-001
(3) Do this task: Stabilizer Trim Limit Switches Adjustment, TASK 27-41-94-820-801.
SUBTASK 27-41-94-710-001
(4) Do this task: Stabilizer Trim Limit Switches Test, TASK 27-41-94-700-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 406
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
E. Put the Airplane Back to Its Usual Condition
SUBTASK 27-41-94-410-001
(1) Close this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 407
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
STABILIZER TRIM LIMIT SWITCHES - ADJUSTMENT/TEST
1. General
A. This procedure has these tasks:
(1) An adjustment of the stabilizer trim limit switches
(2) A test of the stabilizer trim limit switches.
B. The stabilizer trim limit switch is referred to as the "limit switch" in this procedure.
C. There are three limit switches (S144, S145, and S844) and two stabilizer takeoff warning switches
(S132 and S546) on the brackets along the stabilizer jackscrew.
D. This procedure is applicable for all three limit switches.
TASK 27-41-94-820-801
2. Stabilizer Trim Limit Switches Adjustment
(Figure 501)
A. References
Reference Title
20-10-44-400-801 Lockwires Installation (P/B 401)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
COM-1587 Wrench - Torque, 30 in-lbs (4 N-m)
(Part #: TE3FUA, Supplier: 55719, A/P Effectivity: 737-ALL)
SPL-1677 Assembly - Trammel Bar, Stabilizer Trim Actuator
(Part #: F80055-1, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
C. Consumable Materials
Reference Description Specification
G01505 Lockwire - Safety And Lock NASM20995
D. Location Zones
Zone Area
311 Area Aft of Pressure Bulkhead - Left
312 Area Aft of Pressure Bulkhead - Right
E. Access Panels
Number Name/Location
311BL Stabilizer Trim Access Door
F. Prepare for the Test
SUBTASK 27-41-94-010-002
(1) To get access to the limit switches, do this step:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 501
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Open this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
SUBTASK 27-41-94-860-004
(2) Use the bar, SPL-1677 to set the applicable "B" dimensions as follows:
(a) With the stabilizer autopilot and electric actuator nose down (flaps not up), make sure the
switch S145 "B" dimension at 0.05 units of trim is 45.48 ±0.05 in. (1155.2 ±1.3 mm).
GUN 101-122
(b) With the stabilizer electric actuator nose down (flaps up), make sure the switch S844 "B"
dimension at 4.30 units of trim is 39.46 ±0.05 in. (1002.3 ±1.3 mm).
GUN 001-099, 155-157, 201-999
(c) With the stabilizer electric actuator nose down (flaps up), make sure the switch S844 "B"
dimension at 3.95 units of trim is 39.96 ±0.05 in. (1015.0 ±1.3 mm).
GUN ALL
(d) With the stabilizer autopilot and electric actuator nose up, make sure the switch S144 "B"
dimension at 14.50 units of trim is 24.80 ±0.05 in. (629.9 ±1.3 mm).
G. Stabilizer Trim Limit Switches Adjustment
SUBTASK 27-41-94-820-002
(1) Adjusting the Type 2 style stabilizer trim limit switch, Figure 501 (Sheet 4):
(a) Remove the lockwire from the lockscrews [4].
(b) Loosen the locknut [6].
(c) Loosen the two lockscrews [4].
(d) Use a 3/32 inch (2.4 millimeters) HEX torque wrench ( 30 in-lbs), COM-1587 to turn the worm
gear with no more than 6 in-lb (0.7 Nm) until the limit switch [1] starts to operate (when you
hear a click).
(e) If you can not turn the worm gear with 6 in-lb (0.7 Nm) of torque, then do these steps:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：
737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(23)
