曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Figure 403 (Sheet 4 of 4)/27-51-11-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-11
Page 422
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
INBOARD TRAILING EDGE FLAP - ADJUSTMENT/TEST
1. General
A. This procedure has an adjustment of the inboard trailing edge flap.
B. This procedure includes the adjustment of the main flap with the aft flap either removed or installed.
C. The adjustment instructions included in this procedure are included in the Rigging Diagram - Inbd
and Outbd Flaps, Wing Trailing Edge 113A3017.
TASK 27-51-11-820-801
2. Inboard Trailing Edge Flap Adjustment
A. References
Reference Title
27-09-71-820-801 Trailing Edge Flap Adjustment for Lateral Trim (P/B 501)
27-51-00-040-801 Trailing Edge Flap System Deactivation (P/B 201)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-860-803 Extend the Trailing Edge Flaps (P/B 201)
27-51-00-860-804 Retract the Trailing Edge Flaps (P/B 201)
27-51-00-980-801 Trailing Edge Flap System Manual Operation (P/B 201)
27-51-18-000-802 Inboard Flap Support Aft Fairing Removal (P/B 401)
27-51-18-400-802 Inboard Flap Support Aft Fairing Installation (P/B 401)
27-51-21-820-801 Outboard Trailing Edge Flap Adjustment (P/B 501)
32-00-01-480-801 Landing Gear Downlock Pins Installation (P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1585 Kit - Rigging Pins, All Systems
(Part #: F70207-109, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
STD-4232 Pin, Rig, 0.2500 in (6.35 mm)
C. Consumable Materials
Reference Description Specification
A00247 Sealant - Pressure And Environmental - Chromate
Type
BMS5-95
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
7 Pin 57-42-51-02-155 GUN 001-028, 101-121,
155-157, 201-999
25 Pin 27-51-13-02-150 GUN 001-014, 101-108,
155-157, 201-999
27-51-13-02-380 GUN 001-014, 101-108,
155-157, 201-999
34 Pin 27-51-13-02-380 GUN 001-014, 101-108,
155-157, 201-999
27-51-13-02-470 GUN 001-014, 101-108,
155-157, 201-999
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-11
Page 501
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
AMM Item Description AIPC Reference AIPC Effectivity
69 Seal 27-51-12-01-160 GUN 001-028, 101-121,
155-157, 201-999
E. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
541 Left Wing - Fairing Flap Support No. 4
542 Left Wing - Fairing Flap Support No. 3
553 Left Wing - Inboard Flap
641 Right Wing - Fairing Flap Support No. 5
642 Right Wing - Fairing Flap Support No. 6
653 Right Wing - Inboard Flap
F. Prepare For the Adjustment
SUBTASK 27-51-11-480-003
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR CAN RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) If the downlock pins are not installed in the nose and main landing gear, do this task: Landing
Gear Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-51-11-040-002
(2) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-51-11-010-003
(3) Do this task: Inboard Flap Support Aft Fairing Removal, TASK 27-51-18-000-802.
SUBTASK 27-51-11-820-003
(4) Make sure the outboard flap [1] is adjusted correctly. To adjust the outboard flap [1], do this task:
Outboard Trailing Edge Flap Adjustment, TASK 27-51-21-820-801.
G. Inboard Trailing Edge Flap Adjustment
NOTE: There is no mismatch, or alignment dimension to the outboard flap, or to fixed structure that
the inboard flap is adjusted to meet. The eccentric carriage rollers can be changed from the
nominal position to meet lateral trim tolerances.
SUBTASK 27-51-11-860-005
(1) Do a check of the adjustment of the deflection control roller [12] on the outboard end of the
inboard flap [1] (Figure 501):
(a) Manually extend and retract the inboard flap [1] through its full travel. To extend and retract
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機(jī)維護(hù)手冊4(90)