曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(Continued)
AMM Item Description AIPC Reference AIPC Effectivity
8 (cont.) 27-51-00-24-130 GUN 101-122
F. Location Zones
Zone Area
116 Nose Landing Gear Wheel Well - Right
117 Electrical and Electronics Compartment - Left
118 Electrical and Electronics Compartment - Right
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
211 Flight Compartment - Left
212 Flight Compartment - Right
G. Access Panels
Number Name/Location
112A Forward Access Door
114AC Fwd Nose Wheel Well Upper Access Panel
H. Prepare for the Adjustment
SUBTASK 27-51-00-020-001
(1) For the flap position transmitters on the left and right wings, do this task: Flap Position
Transmitter Removal, TASK 27-58-01-000-801.
NOTE: If you do not remove the flap position transmitters, they can become incorrectly
adjusted.
SUBTASK 27-51-00-860-021
(2) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-51-00-480-014
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR CAN RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(3) If the downlock pins are not installed in the nose and main landing gear, do this task: Landing
Gear Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-51-00-860-022
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TE FLAPS AND
FLAP DRIVE MECHANISMS. THE FLAPS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO EQUIPMENT.
CAUTION: CAREFULLY MONITOR THE FLAP MOVEMENT IF YOU HAVE DONE WORK ON THE
FLAP CONTROL SYSTEM OR THE FLAP DRIVE SYSTEM. IF COMPONENTS ARE NOT
ADJUSTED CORRECTLY, YOU CAN CAUSE DAMAGE TO THE TRAILING EDGE FLAP
SYSTEM.
(4) Use the alternate system or the manual drive to retract the trailing edge flaps to the UP position.
SUBTASK 27-51-00-040-003
(5) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 508
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
I. Trailing Edge Flap Control System Adjustment
SUBTASK 27-51-00-020-002
CAUTION: DISCONNECT THE TORQUE TUBES FROM THE FLAP POWER DRIVE UNIT BEFORE
YOU ADJUST THE FLAP CONTROL SYSTEM. IF THE FLAP DRIVE SYSTEM IS NOT
ADJUSTED CORRECTLY, YOU CAN CAUSE DAMAGE TO THE FLAP SYSTEM.
(1) If the flap drive system is not adjusted correctly, disconnect the torque tubes [18] from the flap
power drive unit [17]:
(a) Install clamp set, SPL-1726 on the torque tubes [18] on each side of the power drive unit
[17].
(b) Remove the screws [14] that attach the coupling sleeves [15] to the splined couplings [16].
(c) Move the coupling sleeves [15] off the splined couplings [16].
(d) Move the torque tubes [18] away from the flap power drive unit [17].
SUBTASK 27-51-00-010-002
(2) Remove the floor panel to get access to the top of the flap control unit [4], do this task:
Passenger Cabin Floor Panel Removal, TASK 53-21-00-000-801.
NOTE: The floor panel is located between stations 706 and 727B on the right side of the
airplane.
SUBTASK 27-51-00-010-003
(3) To get access to the turnbuckles [3] for the cables WFA and WFB [1], do this step:
Open this access panel:
Number Name/Location
112A Forward Access Door
or remove this access panel:
Number Name/Location
114AC Fwd Nose Wheel Well Upper Access Panel
SUBTASK 27-51-00-820-001
(4) Do the adjustment of the flap control lever [7] and cables WFA and WFB [1]:
(a) Put the flap control lever [7] in the rigged position:
1) Move the flap control lever [7] aft until the detent pin is out of the UP detent.
2) Put a 0.19 inch (4.8 millimeter) thick rigging block between the detent pin on the flap
control lever [7] and the upstop on the detent plate.
NOTE: Make sure the rigging block does not go into the flaps UP detent.
(b) Install a clamp to hold the quadrant [6] against the aft side of the stop [5] on the flap control
unit [4].
(c) Remove the clips [2] from the turnbuckles [3] on the cables WFA and WFB [1].
(d) If you installed a new cable [1], do these steps:
1) Use the turnbuckles [3] to adjust the tension in the cables [1] to 275 ±15 pounds (125
±6.8 kilograms).
2) Remove the clamp from the quadrant [6].
3) Remove the rigging block from the flap control lever [7].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(42)