曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Removal, TASK 29-21-00-000-802.
SUBTASK 27-51-00-860-060
(4) Remove system B hydraulic power, do this task: Hydraulic System A or B Power Removal,
TASK 29-11-00-860-805.
SUBTASK 27-51-00-480-008
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR CAN RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(5) If the downlock pins are not installed in the nose and main landing gear, do this task: Landing
Gear Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-51-00-860-061
(6) Move the LE cruise depressurization valve to the closed position (Figure 204):
NOTE: It will be necessary to use the FSEU to operate the LE cruise depressurization valve.
(a) To get access to the main equipment center, do this task.
Open this access panel:
Number Name/Location
117A Electronic Equipment Access Door
(b) Push the ON/OFF button on the front panel of the FSEU to turn on the display.
NOTE: The display will show EXISTING FAULTS?
(c) Push the NO button until OTHER FUNCTNS? shows on the display.
(d) Push the YES button to select OTHER FUNCTNS? on the FSEU.
(e) Push the YES button to select SET OUTPUTS? from the OTHER FUNCTNS? menu.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 216
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(f) Push the YES button to select LE DEPR VALVE? from the SET OUTPUTS? menu.
(g) Push the YES button at the SET ON? display to change the position of the LE cruise
depressurization valve.
NOTE: This will drive the valve to the closed position. The FSEU will automatically
change the position of the valve back to the open position after approximately 75
seconds.
SUBTASK 27-51-00-980-004
(7) Move the manual override handle on the LE cruise depressurization valve to the OFF position
(Figure 205):
NOTE: Do not force movement of the manual override handle with tools.
(a) Remove lockwire from the manual override handle on the LE cruise depressurization
valve.
(b) Move the manual override handle to the OFF position.
(c) If you cannot move the manual override handle on the LE cruise depressurization valve,
then make sure the leading edge and trailing edge surfaces are fully retracted. Then use
the FSEU to operate the valve again.
CAUTION: MAKE SURE YOU USE A 0.316 INCH (8.03 MM) RIG PIN IN THE CRUISE
DEPRESSURIZATION VALVE HANDLE. A SMALLER RIG PIN CAN PERMIT THE
LEADING EDGE FLAPS AND SLATS TO MOVE IF HYDRAULIC POWER IS
SUPPLIED. THIS CAN CAUSE DAMAGE TO THE AIRPLANE.
(d) Install a 0.316 inch (8.03 mm) rig pin in the manual override handle to keep the handle in the
OFF position.
(e) Attach a DO-NOT-REMOVE tag on the rig pin.
SUBTASK 27-51-00-480-011
(8) Install the lock, SPL-1675 to prevent the operation of the standby hydraulic system (Figure 205).
(a) Make sure the ALTERNATE FLAPS ARM switch is in the OFF position.
(b) Disconnect the electrical connector from the leading edge standby drive shutoff valve.
(c) Make sure the manual override lever at the leading edge standby drive shutoff valve is in
position 1.
WARNING: MAKE SURE TO INSTALL THE GROUND LOCK ON THE STANDBY HYDRAULIC
MODULE TO PREVENT ACCIDENTAL STANDBY SYSTEM OPERATION OF THE
LEADING EDGE FLAPS AND SLATS. THE LEADING EDGE FLAPS AND SLATS CAN
MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO
EQUIPMENT.
(d) Install the lock, SPL-1675 on the standby hydraulic module.
(e) Install the lockpin.
I. Trailing Edge Flap Operation With Primary Control
NOTE: Make sure you do the Disable the Leading Edge Slats part of this task before you operate
the trailing edge flaps.
SUBTASK 27-51-00-860-062
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE LEADING EDGE FLAPS AND
SLATS. IF THE LEADING EDGE FLAPS AND SLATS ARE NOT IN THE RETRACTED
POSITION, THEY WILL RETRACT WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN
CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 217
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(WARNING PRECEDES)
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE FLIGHT CONTROL SURFACES, THE
THRUST REVERSERS, AND THE LANDING GEAR. THESE COMPONENTS CAN MOVE
SUDDENLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) Supply system B hydraulic power, do this task: Hydraulic System A or B Pressurization,
TASK 29-11-00-860-801.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(37)