曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(c) Disconnect the electrical connector [2] from the flap position indicator [1].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-58-02
Page 401
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flap Position Indicator Installation
Figure 401/27-58-02-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-58-02
Page 402
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-58-02-400-801
3. Flap Position Indicator Installation
(Figure 401)
A. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
B. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
1 Indicator 27-58-02-01-005 GUN 001-019, 101-110,
155-157, 201-999
27-58-02-01-050 GUN 001-007, 155-157,
201-999
C. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
D. Flap Position Indicator Installation
SUBTASK 27-58-02-420-001
(1) Install the flap position indicator [1] in the panel:
(a) Connect the electrical connector [2] to the flap position indicator [1].
(b) Put the flap position indicator [1] in its position in the panel.
(c) Tighten the adjustment screw [4] on the clamp [3] to hold the flap position indicator [1].
SUBTASK 27-58-02-860-002
(2) Remove the safety tags and close these circuit breakers:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 11 C01443 FC TE FLAP POS/SKEW SNSR & IND RIGHT
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
E. Flap Position Indicator Test
SUBTASK 27-58-02-860-003
(1) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-58-02-860-004
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE FLIGHT CONTROL SURFACES, THE
THRUST REVERSERS, AND THE LANDING GEAR. THESE COMPONENTS CAN MOVE
SUDDENLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO EQUIPMENT.
(2) Supply system B hydraulic power, do this task: Hydraulic System A or B Pressurization,
TASK 29-11-00-860-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-58-02
Page 403
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-58-02-860-005
(3) If the trailing edge flaps are not in the retracted position, do this task: Trailing Edge Flap
System Operation With Primary Control, TASK 27-51-00-860-801.
SUBTASK 27-58-02-710-001
(4) Do the test of the flap position indicator [1] in the UP position:
(a) Make sure the pointers on the flap position indicator [1] are in the UP white band.
(b) Make sure the tips of the pointers on the flap position indicator [1] align in the limit of 0.06
inch (1.5 millimeters).
SUBTASK 27-58-02-860-006
(5) Move the flap control lever to the 40-unit position to extend the flaps.
SUBTASK 27-58-02-710-002
(6) Do the test of the flap position indicator [1] in the 40-unit position:
(a) Make sure the pointers on the flap position indicator [1] are in the 40-unit white band.
(b) Make sure the tips of the pointers on the flap position indicator [1] align in the limit of 0.06
inch (1.5 millimeters).
SUBTASK 27-58-02-720-001
(7) Do a test of the separation of the pointers:
(a) Move the ALTN FLAPS ARM switch to the ARM position.
(b) Open this circuit breaker and install safety tag:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
(c) Move the flap control lever to the 30-unit position.
NOTE: This will reduce the load on the electric motor.
(d) Move the ALTN FLAP control switch to the UP position and hold it until the right pointer is in
the 30-unit white band on the flap position indicator [].
(e) Make sure the left pointer is in the 40-unit white band.
(f) Remove the safety tag and close this circuit breaker:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
(g) Make sure the left pointer moves to the 30-unit white band.
(h) Make sure the tips of the pointers align in the limit of 0.06 inch (1.5 millimeters).
(i) Open this circuit breaker and install safety tag:
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(124)