曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Outboard Trailing Edge Flap
553 Left Wing - Inboard Flap
650 Subzone - Right Wing: Trailing Edge, Aft of Rear Spar, Inboard of
Outboard Trailing Edge Flap
653 Right Wing - Inboard Flap
E. Prepare for the Removal
SUBTASK 27-51-58-860-002
(1) Extend the trailing edge flaps to the 40-unit position. To extend them, do this task: Extend the
Trailing Edge Flaps, TASK 27-51-00-860-803.
SUBTASK 27-51-58-480-004
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR CAN RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) If the downlock pins are not installed in the nose and main landing gear, do this task: Landing
Gear Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-51-58-040-002
(3) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
F. Inboard Wing Flap Torque Tube Removal
SUBTASK 27-51-58-480-002
(1) Install the clamp set, SPL-1726 on the torque tubes inboard and outboard of the applicable
torque tube (Figure 402):
NOTE: The clamp set can be used to stop inadvertent movement of the flap drive system while
the torque tubes are disconnected. If the flap drive system moves, then it will be
necessary to do the flap drive system adjustment.
(a) Put the clamp assembly in its location on the applicable torque tube.
(b) Turn the knob to tighten the clamp assembly on the torque tube.
(c) Turn the rod until it touches the structure to make sure the clamp assembly does not turn.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 409
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-58-020-003
(2) For tube assembly [32] or tube assembly [33], remove the applicable torque tube guard [37]:
NOTE: The tube assembly [31] does not have a torque tube guard [37].
(a) Remove the nuts [36], washers [35], bolts [34] or bolts [38] that attach the torque tube guard
[37].
(b) Remove the torque tube guard [37] from the torque tube.
SUBTASK 27-51-58-020-004
(3) Remove the tube assembly [31], tube assembly [32] or tube assembly [33]:
(a) Remove the screws [6] that attach the coupling sleeves [5] to the splined couplings [4].
(b) Move the coupling sleeves [5] off the splined couplings [4].
(c) Remove the tube assembly [31], tube assembly [32] or tube assembly [33].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 410
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Wing Flap Torque Tube Installation
Figure 403 (Sheet 1 of 3)/27-51-58-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 411
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Wing Flap Torque Tube Installation
Figure 403 (Sheet 2 of 3)/27-51-58-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 412
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Wing Flap Torque Tube Installation
Figure 403 (Sheet 3 of 3)/27-51-58-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 413
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-58-400-802
5. Inboard Wing Flap Torque Tube Installation
(Figure 403)
A. General
(1) This task is applicable to the torque tubes inboard of the seal rib angle gearbox and outboard of
the Tee angle gearbox.
B. References
Reference Title
12-22-51-640-801 Trailing Edge Flap Torque Tube and Torque Tube Support
Lubrication (P/B 301)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-820-802 Trailing Edge Flap Drive System Adjustment (P/B 501)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
C. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1726 Clamp Set - Trailing Edge Flap Torque Tube
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(92)