曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

NOTE: On transmission No. 4, make sure the ball returns are on the outboard side.
On transmission No. 5, make sure the ball returns are on the inboard side.
a) Remove the nuts [59], washers [58], washers [57] and bolts [56] that attach the
ballscrew assembly [42] to the yoke [53].
b) Turn the ballscrew assembly [42] 1808 in the yoke [53].
c) Install the bolts [56], washers [57], washers [58] and nuts [59].
(g) Tighten the nuts [59].
SUBTASK 27-51-31-420-007
(3) Connect the ballscrew assembly [42] with the gimbal [43] to the carriage [47]:
(a) Move the gimbal [43] to the downstop on the ballscrew assembly [42].
NOTE: On transmission No. 4, make sure the ball returns on the ballscrew nut [55] are on
the outboard side. On transmission No. 5, make sure the ball returns on the
ballscrew nut [55] are on the inboard side.
(b) Move the carriage [47] to align with the gimbal [43].
(c) Install the carriage bushings [46] to attach the gimbal [43] to the carriage [47].
(d) Install the bolts [41], washers [45] and nuts [44] that attach the gimbal bushing [46] to the
carriage [47].
(e) Tighten the nuts [44] to 65-75 pound-inches (7.4-8.4 newton-meters) more than the run-on
torque.
SUBTASK 27-51-31-420-008
(4) Install the u joint assembly [70]:
(a) Put the u joint assembly [70] in its position between the transmission assembly [49] and the
tee angle gearbox [69].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 417
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(b) Install the bolts [66] and nuts [67] that attach the u joint assembly [70] to the transmission
assembly [49] and the tee angle gearbox [69].
SUBTASK 27-51-31-640-004
(5) Apply grease, D00633 to the end of the plunger on the torque trip indicator [48] and push it down
around the sides of the plunger.
SUBTASK 27-51-31-640-002
(6) Lubricate the transmission assembly [49] and ballscrew assembly [42], do this task: Inboard
Flap Inboard Ballscrew Lubrication, TASK 12-22-51-640-802.
SUBTASK 27-51-31-210-003
(7) Make sure the torque trip indicator [48] on the transmission assembly [49] is set.
SUBTASK 27-51-31-820-002
(8) Do this task: Trailing Edge Flap Drive System Adjustment, TASK 27-51-00-820-802.
G. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-31-440-002
(1) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
SUBTASK 27-51-31-860-013
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE FLIGHT CONTROL SURFACES, THE
THRUST REVERSERS, AND THE LANDING GEAR. THESE COMPONENTS CAN MOVE
SUDDENLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO EQUIPMENT.
(2) Supply system B hydraulic power, do this task: Hydraulic System A or B Pressurization,
TASK 29-11-00-860-801.
SUBTASK 27-51-31-860-008
(3) Use the primary system to retract the flaps to the retracted position. To retract the flaps, do this
task: Trailing Edge Flap System Operation With Primary Control, TASK 27-51-00-860-801.
SUBTASK 27-51-31-860-009
(4) Use the primary system to extend and retract the flaps. To extend and retract the flaps, do this
task: Trailing Edge Flap System Operation With Primary Control, TASK 27-51-00-860-801.
SUBTASK 27-51-31-210-004
(5) Make sure the torque trip indicator [48] on the transmission assembly [49] is set.
SUBTASK 27-51-31-860-014
(6) Remove system B hydraulic power, do this task: Hydraulic System A or B Power Removal,
TASK 29-11-00-860-805.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 418
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
INBOARD FLAP BALLSCREWS AND GIMBALS - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the outboard ballscrew and gimbal for the inboard flap
(2) An installation of the outboard ballscrew and gimbal for the inboard flap
(3) A removal of the inboard ballscrew and gimbal for the inboard flap
(4) An installation of the inboard ballscrew and gimbal for the inboard flap.
TASK 27-51-32-000-801
2. Inboard Flap Outboard Ballscrew and Gimbal Removal
(Figure 401)
A. General
(1) This task is applicable to the ballscrew and gimbal at flap supports No. 3 and 6.
B. References
Reference Title
27-51-00-040-801 Trailing Edge Flap System Deactivation (P/B 201)
27-51-00-860-803 Extend the Trailing Edge Flaps (P/B 201)
27-51-00-980-801 Trailing Edge Flap System Manual Operation (P/B 201)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(49)