曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(a) If there was corrosion, refer to (SWPM 20-60-03) to correct the problem.
(b) Apply the D5026NS or ZC-026 compound, G50171 to the connector (SWPM 20-60-03).
SUBTASK 27-59-02-420-004
(7) Connect the electrical connector [14] to the flap skew sensor [13].
SUBTASK 27-59-02-860-004
(8) Remove the safety tags and close these circuit breakers:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 11 C01443 FC TE FLAP POS/SKEW SNSR & IND RIGHT
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
SUBTASK 27-59-02-440-001
(9) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-02
Page 206
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-59-02-860-005
(10) Retract the trailing edge flaps to the UP position. To retract the flaps, do this task: Retract the
Trailing Edge Flaps, TASK 27-51-00-860-804.
SUBTASK 27-59-02-730-001
(11) Do this task: Flap Skew Detection System Functional Test, TASK 27-59-00-730-801.
------------------------- END OF TASK ---------------------------
TASK 27-59-02-000-802
4. Outboard Flap Inboard Skew Mechanism Removal
(Figure 202)
A. General
(1) This task is applicable to the flap skew mechanisms installed on flap supports No. 2 and 7.
(2) You can remove the flap skew mechanism with the flap skew sensor [53] either removed or
installed. This task shows the removal with the flap skew sensor [53] installed.
B. References
Reference Title
27-51-00-040-801 Trailing Edge Flap System Deactivation (P/B 201)
27-51-00-860-803 Extend the Trailing Edge Flaps (P/B 201)
C. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
643 Right Wing - Fairing Flap Support No. 7
D. Procedure
SUBTASK 27-59-02-860-006
(1) Extend the trailing edge flaps to the 40-unit position. To extend them, do this task: Extend the
Trailing Edge Flaps, TASK 27-51-00-860-803.
SUBTASK 27-59-02-040-002
(2) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-59-02-860-007
(3) Open these circuit breakers and install safety tags:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 11 C01443 FC TE FLAP POS/SKEW SNSR & IND RIGHT
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
SUBTASK 27-59-02-020-004
(4) Disconnect the electrical connector [54] from the flap skew sensor [53].
SUBTASK 27-59-02-020-005
(5) Remove the nuts [60], washers [59], bushings [58], washers [57] and bolts [56] that attach the
control rod [61] to the crank arm [55] and to the carriage [62].
SUBTASK 27-59-02-020-006
(6) Remove the sensor input assembly [42]:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-02
Page 207
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Remove the nut [47], washer [46], washer [45], washer [44] and bolt [43] that attach the
sensor input assembly [42] and the jumper wire [48] to the flap track [48].
(b) Remove the nuts [52], washers [51], washers [50] and bolts [49] that attach the sensor input
assembly [42] to the flap track [41].
(c) Remove the sensor input assembly [42] from the flap track [41].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-02
Page 208
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Inboard Skew Mechanism Installation
Figure 202 (Sheet 1 of 2)/27-59-02-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-02
Page 209
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Inboard Skew Mechanism Installation
Figure 202 (Sheet 2 of 2)/27-59-02-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-02
Page 210
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-59-02-400-802
5. Outboard Flap Inboard Skew Mechanism Installation
(Figure 202)
A. General
(1) This task is applicable to the flap skew mechanisms installed on flap supports No. 2 and 7.
B. References
Reference Title
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-860-804 Retract the Trailing Edge Flaps (P/B 201)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(137)